Allied Telesis AT-SBX31XZ4, X3112, AT-SBX31FAN, AT-SBX31GP24 manual Unpacking AT-SBx3112 Chassis

Page 52

Chapter 2: Installation

Unpacking the

AT-SBx3112

Chassis

2.Identify the lowest 1/2” screw hole pattern on the rack mounting rails within the space reserved for the AT-SBx3112 Chassis. Install one rack mount screw in each vertical rail - at the same height in the top screw hole of the lowest 1/2” hole pattern as displayed in Figure 22. The screws are used to support the chassis while you secure it to the rack.

Screw

 

Head

 

6.4 mm (.25 in) away from rack

Top screw hole of the lowest 1/2” hole pattern

1791

Figure 22. Rack Mounting Hole Locations

Do NOT fully tighten these two screws at this time. The screw heads should protrude from the rack approximately 6.4 mm (.25 in).

To unpack the AT-SBx3112 Chassis, perform the following procedure:

1. Remove all components from the shipping package.

Note

Store the packaging material in a safe location. You must use the original shipping material if you need to return the unit to Allied Telesis.

52

Image 52
Contents Installation Guide Page Electrical Safety and Emissions Standards Translated Safety Statements Contents Power Specifications List of Figures Tightening Thumb Screws on the AT-SBx31XZ4 XFP Line Card List of Tables List of Tables Preface Safety Symbols Used in this Document Symbol Meaning DescriptionWhere to Find Web-based Guides Management Software Updates Contacting Allied TelesisOverview ChapterIntroduction Component Description ReferenceAT-SBx3112 Chassis Front View of the AT-SBx3112 ChassisAT-SBx3112 Chassis Slots Slot Line Cards/Power Supplies AT-SBx31CFC Fabric Control Card SBx31CFCAT-SBx31CFC Fabric Control Card Features Status LEDs System Status LEDsLED State DescriptionSBx Status LEDs LEDs State DescriptionEco-friendly Button Reset Button Network Management Port Console RS-232 Port USB Port SD Card Slot LEDs State Description AT-SBx31GP24 PoE Line Card Connector Type Speed Duplex Mode Maximum Distance Cable Type Auto MDI/ MDI-X Port Pinouts PoE AT-SBx31GP24 Power over Ethernet Power BudgetingMaximum Range Maximum # Class Usage Ports withAvailable at PoE PSU 1200 W 2400 WImplementation AT-SBx31XZ4 XFP Line Card AT-SBx31XZ4 LEDAT-SBx3161 System Power Supply AT-SBx3161 Status LEDsStatus LED Description on the AT-SBx3161 System Power Supply AT-SBx3165 PoE Power Supply AT-SBx3165 Status LEDsStatus LED Description on the AT-SBx3165 PoE Power Supply AT-SBx31FAN Tray AT-SBx31FAN Tray Power Power LED on the AT-SBx31FAN TrayOverview Installation Reviewing Safety Precautions SwitchBlade x3112 Installation Guide Access location.  E45 Selecting a Site for the SwitchBlade Installing the AT-SBx3112 Chassis Preparing the Equipment Rack Reserving Vertical Rack SpaceUnpacking AT-SBx3112 Chassis Adjusting the Brackets Front Panel Position DimensionFactory Installed Flush with Rack Rails Rack Bracket Locations for Reverse Position of Chassis Installing the AT SBx3112 Chassis Equipment Rack Lifting AT-SBx3112 Chassis into PlaceRemoving the Front Panel Shipping Brace Screws Installing Chassis Ground Lug Attaching the Grounding Wire to the Grounding LugInstall the ground lug as displayed in Figure Protection Against Electrostatic Discharge ESD ESD SocketInstalling the AT-SBx3161 System Power Supply Unlocked Handle on the AT-SBx3161 System Power Supply Lock the Handle on the AT-SBx3161 System Power Supply Installation Installing the AT-SBx3165 PoE Power Supply Inserting the AT-SBx3165 PoE Power Supply 1887 Installing the AT-SBx31CFC Fabric Control Card Aligning the AT-SBx31CFC Card in the Chassis Slot 1825 1826 Installing the AT-SBx31GP24 PoE Line Card 1799 SBx31GP Installing the AT-SBx31XZ4 XFP Line Card Tightening Thumb Screws on the AT-SBx31XZ4 XFP Line Card SwitchBlade x3112 Installation Guide Installing an XFP Transceiver Replacing the AT-SBx31FAN Tray Inserting the AT-SBx31FAN Tray into the Chassis 1FAN Cabling the Twisted-Pair or Fiber Optic Ports Installing the Chassis Blank Panels Applying A/C Power to the SwitchBlade 1853 Installation Starting a Local Management Session SBx31CFCInstallation Troubleshooting Officer SEC Show PSU Officer SEC Show PSU Full Officer SEC Show Fanmodule Officer SEC show card Link LED is Off on AT-SBx31GP24 PoE Line Card Troubleshooting Port LED is Off on AT-SBx31XZ4 XFP Line Card Troubleshooting Cannot Establish a Local Out-of-Band Management Session Troubleshooting Physical Specifications DimensionsWeight Appendix aEnvironmental Specifications Power SpecificationsSafety and Electromagnetic Emissions Certifications EMI/RFIConnectors and Port Pinouts Pin SignalPin Pair Signal Operating Cable RequirementsDistance