Allied Telesis AT-SBX3165, X3112, AT-SBX31FAN manual Installing the AT-SBx3161 System Power Supply

Page 61

SwitchBlade x3112 Installation Guide

Installing the AT-SBx3161 System Power Supply

The SwitchBlade x3112 can host up to four power supplies consisting of two AT-SBx3161 System Power Supplies and two AT-SBx3165 PoE Power Supplies. The AT-SBx3112 Chassis comes with three blank power supply panels in chassis slots A, B, and C as displayed in Figure 33. Slot D is left open for the installation of the first AT-SBx3161 System Power Supply. Keep the blank power supply panels in place on the unused slots to insure proper chassis airflow.

AT-SBx3165 PoE Power Supply Slots		AT-SBx3161 System Power Supply Slots
A	B	C	D
P	P	S	S
O	O	Y	Y
E	E	S	S
		T	T
		E	E
		M	M
			SB 31FAN
			1891

Figure 33. Slots A to D for System and PoE Power Supplies

To install the AT-SBx3161 power supply, perform the following procedure:

1.Choose a slot in the chassis for the AT-SBx3161 System Power Supply. You can install the system power supply in either slot C or D. If this is the initial installation of the chassis, Allied Telesis recommends slot D because it does not have a blank power supply panel installed.

2.If you want to install the power supply in slot C, remove the blank power supply panel by lifting the blank panel handle and lifting the panel out of the slot.

Note

If you are installing one power supply and choose slot C, then install the blank power supply panel that came from slot C and install it in slot D to insure proper chassis airflow. Close the handle to secure it in to the chassis.

Warning

The AT-SBx3161 System Power Supply contains active electronic devices, which can be damaged by electro-static discharges (ESD). Follow the procedure given in “Protection Against Electrostatic Discharge (ESD)” on page 60 to guard against ESD damage when unpacking and installing these power supplies.

61

Image 61

Contents Installation Guide Page Electrical Safety and Emissions Standards Translated Safety Statements Contents Power Specifications List of Figures Tightening Thumb Screws on the AT-SBx31XZ4 XFP Line Card List of Tables List of Tables Preface Symbol Meaning Description Safety Symbols Used in this DocumentWhere to Find Web-based Guides Contacting Allied Telesis Management Software UpdatesChapter OverviewComponent Description Reference IntroductionFront View of the AT-SBx3112 Chassis AT-SBx3112 ChassisAT-SBx3112 Chassis Slots Slot Line Cards/Power Supplies SBx31CFC AT-SBx31CFC Fabric Control CardSystem Status LEDs AT-SBx31CFC Fabric Control Card Features Status LEDsState Description LEDLEDs State Description SBx Status LEDsEco-friendly Button Reset Button Network Management Port Console RS-232 Port USB Port SD Card Slot LEDs State Description AT-SBx31GP24 PoE Line Card Connector Type Speed Duplex Mode Maximum Distance Cable Type Auto MDI/ MDI-X Port Pinouts PoE Power Budgeting AT-SBx31GP24 Power over EthernetPorts with Maximum Range Maximum # Class UsageAvailable at PoE PSU 1200 W 2400 WImplementation AT-SBx31XZ4 XFP Line Card LED AT-SBx31XZ4AT-SBx3161 Status LEDs AT-SBx3161 System Power SupplyStatus LED Description on the AT-SBx3161 System Power Supply AT-SBx3165 Status LEDs AT-SBx3165 PoE Power SupplyStatus LED Description on the AT-SBx3165 PoE Power Supply AT-SBx31FAN Tray Power LED on the AT-SBx31FAN Tray AT-SBx31FAN Tray PowerOverview Installation Reviewing Safety Precautions SwitchBlade x3112 Installation Guide Access location. E45 Selecting a Site for the SwitchBlade Installing the AT-SBx3112 Chassis Reserving Vertical Rack Space Preparing the Equipment RackUnpacking AT-SBx3112 Chassis Front Panel Position Dimension Adjusting the BracketsFactory Installed Flush with Rack Rails Rack Bracket Locations for Reverse Position of Chassis Lifting AT-SBx3112 Chassis into Place Installing the AT SBx3112 Chassis Equipment RackRemoving the Front Panel Shipping Brace Screws Attaching the Grounding Wire to the Grounding Lug Installing Chassis Ground LugInstall the ground lug as displayed in Figure ESD Socket Protection Against Electrostatic Discharge ESDInstalling the AT-SBx3161 System Power Supply Unlocked Handle on the AT-SBx3161 System Power Supply Lock the Handle on the AT-SBx3161 System Power Supply Installation Installing the AT-SBx3165 PoE Power Supply Inserting the AT-SBx3165 PoE Power Supply 1887 Installing the AT-SBx31CFC Fabric Control Card Aligning the AT-SBx31CFC Card in the Chassis Slot 1825 1826 Installing the AT-SBx31GP24 PoE Line Card 1799 SBx31GP Installing the AT-SBx31XZ4 XFP Line Card Tightening Thumb Screws on the AT-SBx31XZ4 XFP Line Card SwitchBlade x3112 Installation Guide Installing an XFP Transceiver Replacing the AT-SBx31FAN Tray Inserting the AT-SBx31FAN Tray into the Chassis 1FAN Cabling the Twisted-Pair or Fiber Optic Ports Installing the Chassis Blank Panels Applying A/C Power to the SwitchBlade 1853 Installation SBx31CFC Starting a Local Management SessionInstallation Troubleshooting Officer SEC Show PSU Officer SEC Show PSU Full Officer SEC Show Fanmodule Officer SEC show card Link LED is Off on AT-SBx31GP24 PoE Line Card Troubleshooting Port LED is Off on AT-SBx31XZ4 XFP Line Card Troubleshooting Cannot Establish a Local Out-of-Band Management Session Troubleshooting Dimensions Physical SpecificationsWeight Appendix aPower Specifications Environmental SpecificationsEMI/RFI Safety and Electromagnetic Emissions CertificationsPin Signal Connectors and Port PinoutsPin Pair Signal Operating Cable RequirementsDistance