Allied Telesis X3112, AT-SBX31FAN, AT-SBX31GP24, AT-SBX31XZ4 Selecting a Site for the SwitchBlade

Page 49

SwitchBlade x3112 Installation Guide

Selecting a Site for the SwitchBlade x3112

Observe the following requirements before installing your switch in an equipment rack:

ˆEnsure that the rack is safely secured and that it will not tip over. Devices in a rack should be installed starting at the bottom, with the heavier devices near the bottom of the rack.

ˆThe power outlet for the switch should be located near the unit and should be easily accessible.

ˆIf the chassis has a system and PoE power supplies installed, the power sources for multiple supplies of the same type should be on different A/C circuits to protect the unit from a power circuit failure.

ˆUse dedicated power circuits or power conditioners to supply reliable electrical power to the network devices.

ˆThe site should provide easy access to the ports on the front of the chassis so that you can easily connect and disconnect the network cables, as well as view the unit’s LEDs.

ˆAir flow around the unit and through the side and rear vents should be unrestricted.

ˆDo not place objects on top of the switch.

ˆDo not expose the switch to moisture or water.

ˆEnsure that the site is a dust-free environment.

49

Image 49
Contents Installation Guide Page Electrical Safety and Emissions Standards Translated Safety Statements Contents Power Specifications List of Figures Tightening Thumb Screws on the AT-SBx31XZ4 XFP Line Card List of Tables List of Tables Preface Symbol Meaning Description Safety Symbols Used in this DocumentWhere to Find Web-based Guides Contacting Allied Telesis Management Software UpdatesChapter OverviewComponent Description Reference IntroductionFront View of the AT-SBx3112 Chassis AT-SBx3112 ChassisAT-SBx3112 Chassis Slots Slot Line Cards/Power Supplies SBx31CFC AT-SBx31CFC Fabric Control CardSystem Status LEDs AT-SBx31CFC Fabric Control Card Features Status LEDsState Description LEDLEDs State Description SBx Status LEDsEco-friendly Button Reset Button Network Management Port Console RS-232 Port USB Port SD Card Slot LEDs State Description AT-SBx31GP24 PoE Line Card Connector Type Speed Duplex Mode Maximum Distance Cable Type Auto MDI/ MDI-X Port Pinouts PoE Power Budgeting AT-SBx31GP24 Power over EthernetPorts with Maximum Range Maximum # Class UsageAvailable at PoE PSU 1200 W 2400 WImplementation AT-SBx31XZ4 XFP Line Card LED AT-SBx31XZ4AT-SBx3161 Status LEDs AT-SBx3161 System Power SupplyStatus LED Description on the AT-SBx3161 System Power Supply AT-SBx3165 Status LEDs AT-SBx3165 PoE Power SupplyStatus LED Description on the AT-SBx3165 PoE Power Supply AT-SBx31FAN Tray Power LED on the AT-SBx31FAN Tray AT-SBx31FAN Tray PowerOverview Installation Reviewing Safety Precautions SwitchBlade x3112 Installation Guide Access location.  E45 Selecting a Site for the SwitchBlade Installing the AT-SBx3112 Chassis Reserving Vertical Rack Space Preparing the Equipment RackUnpacking AT-SBx3112 Chassis Front Panel Position Dimension Adjusting the BracketsFactory Installed Flush with Rack Rails Rack Bracket Locations for Reverse Position of Chassis Lifting AT-SBx3112 Chassis into Place Installing the AT SBx3112 Chassis Equipment RackRemoving the Front Panel Shipping Brace Screws Attaching the Grounding Wire to the Grounding Lug Installing Chassis Ground LugInstall the ground lug as displayed in Figure ESD Socket Protection Against Electrostatic Discharge ESDInstalling the AT-SBx3161 System Power Supply Unlocked Handle on the AT-SBx3161 System Power Supply Lock the Handle on the AT-SBx3161 System Power Supply Installation Installing the AT-SBx3165 PoE Power Supply Inserting the AT-SBx3165 PoE Power Supply 1887 Installing the AT-SBx31CFC Fabric Control Card Aligning the AT-SBx31CFC Card in the Chassis Slot 1825 1826 Installing the AT-SBx31GP24 PoE Line Card 1799 SBx31GP Installing the AT-SBx31XZ4 XFP Line Card Tightening Thumb Screws on the AT-SBx31XZ4 XFP Line Card SwitchBlade x3112 Installation Guide Installing an XFP Transceiver Replacing the AT-SBx31FAN Tray Inserting the AT-SBx31FAN Tray into the Chassis 1FAN Cabling the Twisted-Pair or Fiber Optic Ports Installing the Chassis Blank Panels Applying A/C Power to the SwitchBlade 1853 Installation SBx31CFC Starting a Local Management SessionInstallation Troubleshooting Officer SEC Show PSU Officer SEC Show PSU Full Officer SEC Show Fanmodule Officer SEC show card Link LED is Off on AT-SBx31GP24 PoE Line Card Troubleshooting Port LED is Off on AT-SBx31XZ4 XFP Line Card Troubleshooting Cannot Establish a Local Out-of-Band Management Session Troubleshooting Dimensions Physical SpecificationsWeight Appendix aPower Specifications Environmental SpecificationsEMI/RFI Safety and Electromagnetic Emissions CertificationsPin Signal Connectors and Port PinoutsPin Pair Signal Operating Cable RequirementsDistance