Allied Telesis AT-SBX31XZ4, X3112, AT-SBX31FAN manual Starting a Local Management Session, SBx31CFC

Page 87

SwitchBlade x3112 Installation Guide

Starting a Local Management Session

The procedure in this section explains how to start a local (out-of-band) management session using the RJ-45 terminal port on the AT-SBx31CFC Management Fabric Card. You can use a local management session to configure the switch’s operating parameters and view performance and error statistics.

To start a local management session, perform the following procedure:

1.Connect the RJ-45 end of to the Console RS-232 Port on the front panel of the AT-SBx31CFC Fabric Control Card, as displayed in Figure 58.

2

4

SBx31CFC

SYS S

SBx

M/S

TATUS

STATUS

MASTER

0

PSU

SLAVE

1

NORMAL

2

3

FAULT

4

FAN

NORMAL

M/S

5

CFC

1000

LINK

FAULT

6

7

RESET

PSU

8

10/100

ACT

9

LINK

FAN

10

NET

ACT

SD

11

MGMT

6

READY

BUSY

L/A

CONSOLE

FAULT

10/100/

1000Base-T

RS-232

8

10

1843

Figure 58. Connecting the Management Cable to the Console RS-232 Port

Note

The management cable included with the AT-SBx31CFC Fabric

Control Card.

Connect the other end of the cable to an RS-232 port on a terminal or a personal computer with a terminal emulation program.

2.Configure the terminal or terminal emulation program as follows:

Baud rate: Default is 115,000 bps (Range is 9600 to 115200 bps)

Data bits: 8

Parity: None

Stop bits: 1

Flow control: None

87

Image 87

Contents Installation Guide Page Electrical Safety and Emissions Standards Translated Safety Statements Contents Power Specifications List of Figures Tightening Thumb Screws on the AT-SBx31XZ4 XFP Line Card List of Tables List of Tables Preface Symbol Meaning Description Safety Symbols Used in this DocumentWhere to Find Web-based Guides Contacting Allied Telesis Management Software UpdatesChapter OverviewComponent Description Reference IntroductionFront View of the AT-SBx3112 Chassis AT-SBx3112 ChassisAT-SBx3112 Chassis Slots Slot Line Cards/Power Supplies SBx31CFC AT-SBx31CFC Fabric Control CardSystem Status LEDs AT-SBx31CFC Fabric Control Card Features Status LEDsState Description LEDLEDs State Description SBx Status LEDsEco-friendly Button Reset Button Network Management Port Console RS-232 Port USB Port SD Card Slot LEDs State Description AT-SBx31GP24 PoE Line Card Connector Type Speed Duplex Mode Maximum Distance Cable Type Auto MDI/ MDI-X Port Pinouts PoE Power Budgeting AT-SBx31GP24 Power over Ethernet1200 W 2400 W Maximum Range Maximum # Class UsagePorts with Available at PoE PSUImplementation AT-SBx31XZ4 XFP Line Card LED AT-SBx31XZ4AT-SBx3161 Status LEDs AT-SBx3161 System Power SupplyStatus LED Description on the AT-SBx3161 System Power Supply AT-SBx3165 Status LEDs AT-SBx3165 PoE Power SupplyStatus LED Description on the AT-SBx3165 PoE Power Supply AT-SBx31FAN Tray Power LED on the AT-SBx31FAN Tray AT-SBx31FAN Tray PowerOverview Installation Reviewing Safety Precautions SwitchBlade x3112 Installation Guide Access location. E45 Selecting a Site for the SwitchBlade Installing the AT-SBx3112 Chassis Reserving Vertical Rack Space Preparing the Equipment RackUnpacking AT-SBx3112 Chassis Front Panel Position Dimension Adjusting the BracketsFactory Installed Flush with Rack Rails Rack Bracket Locations for Reverse Position of Chassis Lifting AT-SBx3112 Chassis into Place Installing the AT SBx3112 Chassis Equipment RackRemoving the Front Panel Shipping Brace Screws Attaching the Grounding Wire to the Grounding Lug Installing Chassis Ground LugInstall the ground lug as displayed in Figure ESD Socket Protection Against Electrostatic Discharge ESDInstalling the AT-SBx3161 System Power Supply Unlocked Handle on the AT-SBx3161 System Power Supply Lock the Handle on the AT-SBx3161 System Power Supply Installation Installing the AT-SBx3165 PoE Power Supply Inserting the AT-SBx3165 PoE Power Supply 1887 Installing the AT-SBx31CFC Fabric Control Card Aligning the AT-SBx31CFC Card in the Chassis Slot 1825 1826 Installing the AT-SBx31GP24 PoE Line Card 1799 SBx31GP Installing the AT-SBx31XZ4 XFP Line Card Tightening Thumb Screws on the AT-SBx31XZ4 XFP Line Card SwitchBlade x3112 Installation Guide Installing an XFP Transceiver Replacing the AT-SBx31FAN Tray Inserting the AT-SBx31FAN Tray into the Chassis 1FAN Cabling the Twisted-Pair or Fiber Optic Ports Installing the Chassis Blank Panels Applying A/C Power to the SwitchBlade 1853 Installation SBx31CFC Starting a Local Management SessionInstallation Troubleshooting Officer SEC Show PSU Officer SEC Show PSU Full Officer SEC Show Fanmodule Officer SEC show card Link LED is Off on AT-SBx31GP24 PoE Line Card Troubleshooting Port LED is Off on AT-SBx31XZ4 XFP Line Card Troubleshooting Cannot Establish a Local Out-of-Band Management Session Troubleshooting Appendix a Physical SpecificationsDimensions WeightPower Specifications Environmental SpecificationsEMI/RFI Safety and Electromagnetic Emissions CertificationsPin Signal Connectors and Port PinoutsPin Pair Signal Cable Requirements OperatingDistance