NetComm Gateway Series manual Stun client

Page 14

The table shown below lists possible solutions for different network scenarios.

LAN IP address of Internet sharing

Please avoid IP address 192.168.8.1-192.168.8.254 (You may need to

 

change the settings of Internet sharing device or change the SmartVoice

 

gateway LAN Port IP address)

 

 

 

 

 

WAN IP of SmartVoice gateway

Set as a static private IP address or DHCP; when the WAN port is set as a

 

static private IP, assign the LAN IP address of the Internet sharing to as default

 

gateway IP of SmartVoice gateway; When the WAN IP is set as DHCP, please

 

make sure you have DHCP server running in network to issue an IP to the

 

SmartVoice gateway.

 

 

 

 

 

 

NAT Traversal

NAT Public IP

If the WAN of the IP sharing device has a static public IP

There are three ways to configure

 

address, then the “NAT IP/Domain” address is set as the

 

Public IP address of the Internet sharing devices.

a SmartVoice gateway to traversing

 

 

 

 

NAT in Internet sharing devices. For

 

If the WAN of the Internet sharing device uses a dynamic

details, please refer to page 26.

 

public IP address and you specify a domain name in “NAT

 

 

IP/Domain” field, which has to comply with the DDNS

 

 

settings.

 

 

 

Note: you also need to forward specific ports on the NAT

 

 

router to the WAN port of the SmartVoice gateway.

 

 

 

 

 

 

Enable STUN client will avoid problems of configuring port

 

STUN client

forwarding in the Internet sharing device, but some NAT

 

routers do not support STUN.

 

 

 

 

 

 

Using UPnP to enable the SmartVoice gateway to pass

 

UPnP Control

through NAT of Internet sharing device. This function only

 

point

works when the Internet sharing devices support UPnP

 

and has it enabled.

 

 

 

 

 

 

 

 

DDNS Settings

The WAN of the Internet sharing device

(Unnecessary) Disabled

For details, please refer to page 27

has a static public IP address.

 

 

 

 

for the DDNS Settings

 

 

 

The WAN of the Internet sharing device

Enabled: enter the registered

 

 

has a dynamic IP address.

URL (Uniform Resource Locator)

 

 

 

and DDNS server info into

 

 

 

corresponding areas.

 

 

 

 

14

SmartVoice Gateway(s) User Guide

 

YML832 Rev2

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Reference Guide Contents Important Note To ensure your Gateway complies with Australian StandardsIntroduction Product OverviewItems that you will need and things you will need to know Broadband ServiceVoIP Service Computer/NetworkAdvance Firewall and DoS Protection NetComm SmartVoice Gateway FeaturesVoice Features Configuration & Maintenance Network General SpecificationsFeatures are only available in models which have FXO ports SmartVoice Gateways User Guide YML832 Rev2 Restore the Gateway Rear Panel all modelsInstallation and Applications Connecting your SmartVoice GatewaysNetwork requirements Network ConnectionsGateway Assigned with a Public IP Address Gateway behind a NAT/Firewall Network RequirementsStun client Needs to be set up as either in static IP, DHCP, or PPPoE Telephone Connection Integrating the SmartVoice Gateway with PBXIntegrating the SmartVoice Gateway with PBX Integrating the SmartVoice Gateway with PBX Configuring the Gateway via WEB Browser InstructionsNetwork Settings IP Configuration Setting WAN PortSetting Dynamic IP Dhcp DNS Settings Clone MACLAN interface mode Network Settings LANQoS Settings WAN QoSNAT/DDNS NAT Traversal Ddns ExampleTelephony Settings Prefix Number RulesFXO Line VoIP call in options Hotline FunctionsDescription SIP Settings 164 SmartVoice Gateways User Guide FXS/ FXO Representative number registers to Proxy Each line registers to Proxy independentlyServer Settings Private NetworkPrivate Network Numbers Calling Features Calling Feature InstructionsAdvanced Options Payload Type payload type of RFC2833 Line Settings Flash TimeCodec Settings Fax Settings Drop Inactive Call Digit Map Phone Book Speed Dial Caller Filter Transit Call Control Dialing principle to enable PIN code Gateway a PIN Code * Gateway B NumberLong-Distance Control Table Long Distance Exception TableCPT parameters Table CPT/Cadence SettingsBusy Tone Cadence Measurement CPT Auto Detect Direct Connection to Pstn SmartVoice Gateways User Guide YML832 Rev2 Connected to a PBX Extension Line 36008914 Save Settings Filling in the CPT TableCurrent Status and System Information RTP Packet Summary Stun Inquiry Ping Test Port Filtering IP Filtering MAC Filtering Virtual Server DMZ URL Filter Special Applications DoS Prevention Settings Enable Source IP Blocking Block the IP Backup and Restore Configuration NTP Network Time ProtocolProvision Settings System Operations Save Settings Software Upgrade Logout Preparation Configuring the Gateway via IVRConfiguration Methods IVR Interactive Voice Response Inquire Current Gateway’s WAN Port IP addressIVR Functions Table DNS IP address Set/QuerySet/Query Gateway Telephone Number Representative Number IP Configuration Settings WAN port Static IP Settings Adsl PPPoE SettingsSave Settings and Restart PPPoE Account SettingsPPPoE Password Setting Select PPPoEPPPoE Character Conversion Table Dialed Number Processing Flow Dialing and dialed number routing principleInstruction End Appendix a Glossary 10BASE-TDNS Http NAT TCP VSP Appendix B Cable Information RJ-45 Network PortsCross-Over Cabling Straight and crossover cable configurationStraight-Through Cabling Appendix C Registration and Warranty Information Contact InformationProduct Warranty PO Box 1200, Lane Cove NSW 2066 Australia
Top Page Image Contents