NetComm Gateway Series manual Appendix B Cable Information, RJ-45 Network Ports

Page 90

Appendix B: Cable Information

This cable information is provided for your reference only. Please ensure you only connect the appropriate cable into the correct socket on either this product or your computer.

If you are unsure about which cable to use or which socket to connect it to, please refer to the hardware installation section in this manual. If you are still not sure about cable connections, please contact a professional computer technician or NetComm for further advice.

RJ-45 Network Ports

RJ-45 Network Ports can connect any networking devices that use a standard LAN interface, such as a Hub/Switch Hub or Router. Use unshielded twisted-pair (UTP) or shield twisted-pair (STP) cable to connect the networking device to the RJ-45 Ethernet port. Depending on the type of connection, 10Mbps or 100Mbps, use the following Ethernet cable, as prescribed.

10Mbps:

Use EIA/TIA-568-100-Category 3, 4 or 5 cable.

100Mbps:

Use EIA/TIA-568-100-Category 5 cable.

Note:

To prevent loss of signal, make sure that the length of any twisted-pair connection

 

does not exceed 100 metres.

 

 

 

 

 

 

 

 

 

 

RJ-45 Connector

 

 

 

 

 

Pin Assignment

 

Normal Assignment

 

 

 

 

 

 

 

 

 

1

 

Input Receive Data +

 

 

 

2

 

Input Receive Data -

 

 

 

3

 

Output Transmit Data +

 

 

 

6

 

Output Transmit Data -

 

 

 

4,5,7,8

 

Not used

 

 

 

 

 

 

 

Figure 1

RJ-45 plug attached to cable

Figure 2

90

SmartVoice Gateway(s) User Guide

 

YML832 Rev2

Image 90
Contents Reference Guide Contents Important Note To ensure your Gateway complies with Australian StandardsIntroduction Product OverviewItems that you will need and things you will need to know Broadband ServiceVoIP Service Computer/NetworkNetComm SmartVoice Gateway Features Voice FeaturesAdvance Firewall and DoS Protection Configuration & Maintenance General Specifications Features are only available in models which have FXO portsNetwork SmartVoice Gateways User Guide YML832 Rev2 Restore the Gateway Rear Panel all modelsInstallation and Applications Connecting your SmartVoice GatewaysNetwork Connections Gateway Assigned with a Public IP AddressNetwork requirements Gateway behind a NAT/Firewall Network RequirementsStun client Needs to be set up as either in static IP, DHCP, or PPPoE Telephone Connection Integrating the SmartVoice Gateway with PBXIntegrating the SmartVoice Gateway with PBX Integrating the SmartVoice Gateway with PBX Configuring the Gateway via WEB Browser InstructionsNetwork Settings IP Configuration Setting WAN PortSetting Dynamic IP Dhcp DNS Settings Clone MACLAN interface mode Network Settings LANQoS Settings WAN QoSNAT/DDNS NAT Traversal Ddns ExampleTelephony Settings Prefix Number RulesFXO Line VoIP call in options Hotline FunctionsDescription SIP Settings 164 SmartVoice Gateways User Guide FXS/ FXO Representative number registers to Proxy Each line registers to Proxy independentlyServer Settings Private NetworkPrivate Network Numbers Calling Features Calling Feature InstructionsAdvanced Options Payload Type payload type of RFC2833 Line Settings Flash TimeCodec Settings Fax Settings Drop Inactive Call Digit Map Phone Book Speed Dial Caller Filter Transit Call Control Dialing principle to enable PIN code Gateway a PIN Code * Gateway B NumberLong-Distance Control Table Long Distance Exception TableCPT/Cadence Settings Busy Tone Cadence MeasurementCPT parameters Table CPT Auto Detect Direct Connection to Pstn SmartVoice Gateways User Guide YML832 Rev2 Connected to a PBX Extension Line 36008914 Save Settings Filling in the CPT TableCurrent Status and System Information RTP Packet Summary Stun Inquiry Ping Test Port Filtering IP Filtering MAC Filtering Virtual Server DMZ URL Filter Special Applications DoS Prevention Settings Enable Source IP Blocking Block the IP Backup and Restore Configuration NTP Network Time ProtocolProvision Settings System Operations Save Settings Software Upgrade Logout Configuring the Gateway via IVR Configuration MethodsPreparation IVR Interactive Voice Response Inquire Current Gateway’s WAN Port IP addressIVR Functions Table DNS IP address Set/QuerySet/Query Gateway Telephone Number Representative Number IP Configuration Settings WAN port Static IP Settings Adsl PPPoE SettingsSave Settings and Restart PPPoE Account SettingsPPPoE Password Setting Select PPPoEPPPoE Character Conversion Table Dialing and dialed number routing principle InstructionDialed Number Processing Flow End Appendix a Glossary 10BASE-TDNS Http NAT TCP VSP Appendix B Cable Information RJ-45 Network PortsStraight and crossover cable configuration Straight-Through CablingCross-Over Cabling Appendix C Registration and Warranty Information Contact InformationProduct Warranty PO Box 1200, Lane Cove NSW 2066 Australia