NetComm Gateway Series manual Setting Dynamic IP Dhcp

Page 21

Setting Dynamic IP (DHCP)

Click “DHCP” to obtain a Dynamic IP address, and then click the “Accept” button at the bottom of the screen.

To save the settings click System Operation to select “Save Settings”, “Restart”, and then click the ”Accept” button. Wait for a while (about 40 seconds), and the system will obtain the related IP value from the DHCP Server.

NOTE: After the system has obtained a new IP address, if using WAN Port to enter the Web Configuration Screen, a new IP address has to be used. The same applies to the following two settings.

Setting Static IP

Select “Static IP” and enter the IP address, Subnet Mask and Default Gateway values. Then click the “Accept” button at the bottom of the screen.

Save the settings, and then restart the system. Wait for about 40 seconds for the system to restart.

ADSL PPPoE Settings

Select “PPPoE” and enter the Account Number, Password and re-enter Password to confirm. Then click the “Accept” button at the bottom.

Save the settings, and then restart the system. The system will take about 40 seconds to restart.

SmartVoice Gateway(s) User Guide

1

YML832 Rev2

 

Image 21
Contents Reference Guide Contents To ensure your Gateway complies with Australian Standards Important NoteProduct Overview IntroductionVoIP Service Broadband ServiceItems that you will need and things you will need to know Computer/NetworkNetComm SmartVoice Gateway Features Voice FeaturesAdvance Firewall and DoS Protection Configuration & Maintenance General Specifications Features are only available in models which have FXO portsNetwork SmartVoice Gateways User Guide YML832 Rev2 Rear Panel all models Restore the GatewayConnecting your SmartVoice Gateways Installation and ApplicationsNetwork Connections Gateway Assigned with a Public IP AddressNetwork requirements Requirements Gateway behind a NAT/Firewall NetworkStun client Needs to be set up as either in static IP, DHCP, or PPPoE Integrating the SmartVoice Gateway with PBX Telephone ConnectionIntegrating the SmartVoice Gateway with PBX Integrating the SmartVoice Gateway with PBX Instructions Configuring the Gateway via WEB BrowserIP Configuration Setting WAN Port Network SettingsSetting Dynamic IP Dhcp Clone MAC DNS SettingsNetwork Settings LAN LAN interface modeWAN QoS QoS SettingsNAT/DDNS NAT Traversal Example DdnsPrefix Number Rules Telephony SettingsHotline Functions FXO Line VoIP call in optionsDescription SIP Settings 164 SmartVoice Gateways User Guide Each line registers to Proxy independently FXS/ FXO Representative number registers to ProxyPrivate Network Server SettingsPrivate Network Numbers Calling Feature Instructions Calling FeaturesAdvanced Options Payload Type payload type of RFC2833 Flash Time Line SettingsCodec Settings Fax Settings Drop Inactive Call Digit Map Phone Book Speed Dial Caller Filter Transit Call Control Gateway a PIN Code * Gateway B Number Dialing principle to enable PIN codeLong Distance Exception Table Long-Distance Control TableCPT/Cadence Settings Busy Tone Cadence MeasurementCPT parameters Table CPT Auto Detect Direct Connection to Pstn SmartVoice Gateways User Guide YML832 Rev2 Connected to a PBX Extension Line 36008914 Filling in the CPT Table Save SettingsCurrent Status and System Information RTP Packet Summary Stun Inquiry Ping Test Port Filtering IP Filtering MAC Filtering Virtual Server DMZ URL Filter Special Applications DoS Prevention Settings Enable Source IP Blocking Block the IP NTP Network Time Protocol Backup and Restore ConfigurationProvision Settings System Operations Save Settings Software Upgrade Logout Configuring the Gateway via IVR Configuration MethodsPreparation Inquire Current Gateway’s WAN Port IP address IVR Interactive Voice ResponseDNS IP address Set/Query IVR Functions TableSet/Query Gateway Telephone Number Representative Number Adsl PPPoE Settings IP Configuration Settings WAN port Static IP SettingsPPPoE Password Setting PPPoE Account SettingsSave Settings and Restart Select PPPoEPPPoE Character Conversion Table Dialing and dialed number routing principle InstructionDialed Number Processing Flow End 10BASE-T Appendix a GlossaryDNS Http NAT TCP VSP RJ-45 Network Ports Appendix B Cable InformationStraight and crossover cable configuration Straight-Through CablingCross-Over Cabling Contact Information Appendix C Registration and Warranty InformationProduct Warranty PO Box 1200, Lane Cove NSW 2066 Australia