NetComm Gateway Series IP Configuration Settings WAN port Static IP Settings, Adsl PPPoE Settings

Page 79

IP Configuration Settings (WAN port)

Static IP Settings

NOTE: Complete static public/private IP settings should include a static IP (Option
1 under 114), IP address (111), Subnet Mask (112), and Default Gateway (113).
Please contact your local Internet Service Provider (ISP) if you have any questions.

Function	Command
Select a Static IP	• After entering IVR mode, dial 114.
	• After hearing “Enter value”, dial 1 (to select static IP)
IP address Settings	• After entering IVR mode, dial 111. After hearing “Enter value”, enter
	your IP address, followed by “#”.
	Example: If the IP address is 192.168.1.200, dial 1921681*200#.
Subnet Mask Settings	• After entering IVR mode, dial 112. After hearing “Enter value”, enter
	your subnet mask, followed by “#”.
	Example: If the mask value is 255.255.255.0, dial 255255255*0#.
Default Gateway Settings	• After entering IVR mode, dial 113. After hearing “Enter value”, enter
	your default gateway’s IP address, followed by “#”.
	Example: If the Default Gateway is 192.168.1.254, dial 1921681*254#.
Save Settings and Restart	• To save settings, dial 509 (Save Settings). The system will save the
	settings. Please restart the system. Wait for about 40 seconds for the
	system to restart, and then enter 101 to check if the IP address is
	retained. If the IP address is not repeated, it indicates that Gateway has
	not been properly connected; please check if the cable connection is
	correct.
Dynamic IP (DHCP) Settings

After entering IVR mode, dial 114.

After hearing “Enter value”, dial 2 (to select DHCP).

Saving settings –press 509 (Save Settings). Please restart the system. After the system is restarted, press 101 to check if the IP address is retained.

NOTE: If the system does not repeat the IP address, it indicates that the Gateway failed to communicate with a DHCP server. Please check your DHCP server or consult your ISP if they issue an IP address to you via DHCP protocol.

ADSL PPPoE Settings

NOTE: Complete PPPoE settings should include: Select PPPoE (Option 3 of 114), PPPoE account (121) and PPPoE password (122).

Please contact your local Internet Service Provider (ISP) if you have any questions.

SmartVoice Gateway(s) User Guide	79
YML832 Rev2

Image 79

Contents Reference Guide Contents To ensure your Gateway complies with Australian Standards Important NoteProduct Overview IntroductionComputer/Network Broadband ServiceVoIP Service Items that you will need and things you will need to knowVoice Features NetComm SmartVoice Gateway FeaturesAdvance Firewall and DoS Protection Configuration & Maintenance Features are only available in models which have FXO ports General SpecificationsNetwork SmartVoice Gateways User Guide YML832 Rev2 Rear Panel all models Restore the GatewayConnecting your SmartVoice Gateways Installation and ApplicationsGateway Assigned with a Public IP Address Network ConnectionsNetwork requirements Requirements Gateway behind a NAT/Firewall NetworkStun client Needs to be set up as either in static IP, DHCP, or PPPoE Integrating the SmartVoice Gateway with PBX Telephone ConnectionIntegrating the SmartVoice Gateway with PBX Integrating the SmartVoice Gateway with PBX Instructions Configuring the Gateway via WEB BrowserIP Configuration Setting WAN Port Network SettingsSetting Dynamic IP Dhcp Clone MAC DNS SettingsNetwork Settings LAN LAN interface modeWAN QoS QoS SettingsNAT/DDNS NAT Traversal Example DdnsPrefix Number Rules Telephony SettingsHotline Functions FXO Line VoIP call in optionsDescription SIP Settings 164 SmartVoice Gateways User Guide Each line registers to Proxy independently FXS/ FXO Representative number registers to ProxyPrivate Network Server SettingsPrivate Network Numbers Calling Feature Instructions Calling FeaturesAdvanced Options Payload Type payload type of RFC2833 Flash Time Line SettingsCodec Settings Fax Settings Drop Inactive Call Digit Map Phone Book Speed Dial Caller Filter Transit Call Control Gateway a PIN Code * Gateway B Number Dialing principle to enable PIN codeLong Distance Exception Table Long-Distance Control TableBusy Tone Cadence Measurement CPT/Cadence SettingsCPT parameters Table CPT Auto Detect Direct Connection to Pstn SmartVoice Gateways User Guide YML832 Rev2 Connected to a PBX Extension Line 36008914 Filling in the CPT Table Save SettingsCurrent Status and System Information RTP Packet Summary Stun Inquiry Ping Test Port Filtering IP Filtering MAC Filtering Virtual Server DMZ URL Filter Special Applications DoS Prevention Settings Enable Source IP Blocking Block the IP NTP Network Time Protocol Backup and Restore ConfigurationProvision Settings System Operations Save Settings Software Upgrade Logout Configuration Methods Configuring the Gateway via IVRPreparation Inquire Current Gateway’s WAN Port IP address IVR Interactive Voice ResponseDNS IP address Set/Query IVR Functions TableSet/Query Gateway Telephone Number Representative Number Adsl PPPoE Settings IP Configuration Settings WAN port Static IP SettingsSelect PPPoE PPPoE Account SettingsPPPoE Password Setting Save Settings and RestartPPPoE Character Conversion Table Instruction Dialing and dialed number routing principleDialed Number Processing Flow End 10BASE-T Appendix a GlossaryDNS Http NAT TCP VSP RJ-45 Network Ports Appendix B Cable InformationStraight-Through Cabling Straight and crossover cable configurationCross-Over Cabling Contact Information Appendix C Registration and Warranty InformationProduct Warranty PO Box 1200, Lane Cove NSW 2066 Australia