NetComm Gateway Series manual CPT Auto Detect

Page 51

NOTE: To cope with different local PSTN and different PBX models, the system provides auto busy tone cadence learning to prevent the FXO from engaging a line. However, if the line of the receiving party is engaged and his/her PSTN uses a voice prompt to replace the traditional beep sound, then the system would not be able to detect a busy tone. Silence detection should then be used to determine whether or not to end the call.

CPT Auto Detect

2 PSTN phone numbers or 2 PBX extension lines are needed.

Connect one of the phone sets to a FXO port.

The line of “Dial Number” must be on-hook. Set the outgoing phone number the same as the phone line that is in use as above, and click the “Accept” button to start detection.

If detection is successful, the parameters obtained will automatically be inserted into the CPT parameter.

Save settings and restart the system.

Detailed description is given below:

Click “CPT auto detect” at the bottom of Trunk CPT Settings.

If CPT auto detect is used, the function would halt every operation of the Gateway. Select “I am sure of it”, and then click the“Accept”button. Wait for 15 seconds,and then you will enter CPT auto detect window.

SmartVoice Gateway(s) User Guide

51

YML832 Rev2

 

Image 51
Contents Reference Guide Contents To ensure your Gateway complies with Australian Standards Important NoteProduct Overview IntroductionComputer/Network Broadband ServiceVoIP Service Items that you will need and things you will need to knowNetComm SmartVoice Gateway Features Voice FeaturesAdvance Firewall and DoS Protection Configuration & Maintenance General Specifications Features are only available in models which have FXO portsNetwork SmartVoice Gateways User Guide YML832 Rev2 Rear Panel all models Restore the GatewayConnecting your SmartVoice Gateways Installation and ApplicationsNetwork Connections Gateway Assigned with a Public IP AddressNetwork requirements Requirements Gateway behind a NAT/Firewall NetworkStun client Needs to be set up as either in static IP, DHCP, or PPPoE Integrating the SmartVoice Gateway with PBX Telephone ConnectionIntegrating the SmartVoice Gateway with PBX Integrating the SmartVoice Gateway with PBX Instructions Configuring the Gateway via WEB BrowserIP Configuration Setting WAN Port Network SettingsSetting Dynamic IP Dhcp Clone MAC DNS SettingsNetwork Settings LAN LAN interface modeWAN QoS QoS SettingsNAT/DDNS NAT Traversal Example DdnsPrefix Number Rules Telephony SettingsHotline Functions FXO Line VoIP call in optionsDescription SIP Settings 164 SmartVoice Gateways User Guide Each line registers to Proxy independently FXS/ FXO Representative number registers to ProxyPrivate Network Server SettingsPrivate Network Numbers Calling Feature Instructions Calling FeaturesAdvanced Options Payload Type payload type of RFC2833 Flash Time Line SettingsCodec Settings Fax Settings Drop Inactive Call Digit Map Phone Book Speed Dial Caller Filter Transit Call Control Gateway a PIN Code * Gateway B Number Dialing principle to enable PIN codeLong Distance Exception Table Long-Distance Control TableCPT/Cadence Settings Busy Tone Cadence MeasurementCPT parameters Table CPT Auto Detect Direct Connection to Pstn SmartVoice Gateways User Guide YML832 Rev2 Connected to a PBX Extension Line 36008914 Filling in the CPT Table Save SettingsCurrent Status and System Information RTP Packet Summary Stun Inquiry Ping Test Port Filtering IP Filtering MAC Filtering Virtual Server DMZ URL Filter Special Applications DoS Prevention Settings Enable Source IP Blocking Block the IP NTP Network Time Protocol Backup and Restore ConfigurationProvision Settings System Operations Save Settings Software Upgrade Logout Configuring the Gateway via IVR Configuration MethodsPreparation Inquire Current Gateway’s WAN Port IP address IVR Interactive Voice ResponseDNS IP address Set/Query IVR Functions TableSet/Query Gateway Telephone Number Representative Number Adsl PPPoE Settings IP Configuration Settings WAN port Static IP SettingsSelect PPPoE PPPoE Account SettingsPPPoE Password Setting Save Settings and RestartPPPoE Character Conversion Table Dialing and dialed number routing principle InstructionDialed Number Processing Flow End 10BASE-T Appendix a GlossaryDNS Http NAT TCP VSP RJ-45 Network Ports Appendix B Cable InformationStraight and crossover cable configuration Straight-Through CablingCross-Over Cabling Contact Information Appendix C Registration and Warranty InformationProduct Warranty PO Box 1200, Lane Cove NSW 2066 Australia