NetComm Gateway Series manual 36008914

Page 55

Connected to a PBX extension line to detect the busy tone of PSTN

	307
36008913
	36008914
	301
Note:	The above diagrams show a 4-port SmartVoice gateway for illustration purposes.
	An 8 port SmartVoice gateway could also be used depending upon your network
	requirements.

•Connect one of the PBX extension lines to the gateway’s FXO Port.

•Detect Channel: Enter 3 (if the trunk line is connected to P3, and uses P3 for outgoing detection).

•Phone Number: Set the number of FXO line –to detect Reorder Tone.

•Dial Number: Enter the trunk prefix of a PBX, comma, and the number of the end to be tested -- 0,36008913. (Assuming that an extension line is set to dial 0 to make outgoing calls).

•CPT group: Enter the group to save your settings to once the test has been completed. If connecting the gateway to a PBX extension line, please do not set the detected busy tone of the PBX and the PSTN in the same set, otherwise the value detected the first time will be overwritten.

•Finally, click the “Accept” button.

SmartVoice Gateway(s) User Guide	55
YML832 Rev2

Image 55

Contents Reference Guide Contents To ensure your Gateway complies with Australian Standards Important NoteProduct Overview IntroductionComputer/Network Broadband ServiceVoIP Service Items that you will need and things you will need to knowVoice Features NetComm SmartVoice Gateway FeaturesAdvance Firewall and DoS Protection Configuration & Maintenance Features are only available in models which have FXO ports General SpecificationsNetwork SmartVoice Gateways User Guide YML832 Rev2 Rear Panel all models Restore the GatewayConnecting your SmartVoice Gateways Installation and ApplicationsGateway Assigned with a Public IP Address Network ConnectionsNetwork requirements Requirements Gateway behind a NAT/Firewall NetworkStun client Needs to be set up as either in static IP, DHCP, or PPPoE Integrating the SmartVoice Gateway with PBX Telephone ConnectionIntegrating the SmartVoice Gateway with PBX Integrating the SmartVoice Gateway with PBX Instructions Configuring the Gateway via WEB BrowserIP Configuration Setting WAN Port Network SettingsSetting Dynamic IP Dhcp Clone MAC DNS SettingsNetwork Settings LAN LAN interface modeWAN QoS QoS SettingsNAT/DDNS NAT Traversal Example DdnsPrefix Number Rules Telephony SettingsHotline Functions FXO Line VoIP call in optionsDescription SIP Settings 164 SmartVoice Gateways User Guide Each line registers to Proxy independently FXS/ FXO Representative number registers to ProxyPrivate Network Server SettingsPrivate Network Numbers Calling Feature Instructions Calling FeaturesAdvanced Options Payload Type payload type of RFC2833 Flash Time Line SettingsCodec Settings Fax Settings Drop Inactive Call Digit Map Phone Book Speed Dial Caller Filter Transit Call Control Gateway a PIN Code * Gateway B Number Dialing principle to enable PIN codeLong Distance Exception Table Long-Distance Control TableBusy Tone Cadence Measurement CPT/Cadence SettingsCPT parameters Table CPT Auto Detect Direct Connection to Pstn SmartVoice Gateways User Guide YML832 Rev2 Connected to a PBX Extension Line 36008914 Filling in the CPT Table Save SettingsCurrent Status and System Information RTP Packet Summary Stun Inquiry Ping Test Port Filtering IP Filtering MAC Filtering Virtual Server DMZ URL Filter Special Applications DoS Prevention Settings Enable Source IP Blocking Block the IP NTP Network Time Protocol Backup and Restore ConfigurationProvision Settings System Operations Save Settings Software Upgrade Logout Configuration Methods Configuring the Gateway via IVRPreparation Inquire Current Gateway’s WAN Port IP address IVR Interactive Voice ResponseDNS IP address Set/Query IVR Functions TableSet/Query Gateway Telephone Number Representative Number Adsl PPPoE Settings IP Configuration Settings WAN port Static IP SettingsSelect PPPoE PPPoE Account SettingsPPPoE Password Setting Save Settings and RestartPPPoE Character Conversion Table Instruction Dialing and dialed number routing principleDialed Number Processing Flow End 10BASE-T Appendix a GlossaryDNS Http NAT TCP VSP RJ-45 Network Ports Appendix B Cable InformationStraight-Through Cabling Straight and crossover cable configurationCross-Over Cabling Contact Information Appendix C Registration and Warranty InformationProduct Warranty PO Box 1200, Lane Cove NSW 2066 Australia