NetComm Gateway Series manual Network Settings, IP Configuration Setting WAN Port

Page 20

Network Settings

The network settings are used to set the gateway’s communication ports, IP configurations, DNS and DHCP server etc.

•Current WAN IP Address: The IP address of the WAN port.

•Listen Port UDP: It is not necessary to change the protocol of the communication port used by the gateway, unless it conflicts with ports used by another device in your network.

•RTP Starting Port UDP: The initial value of the port number for transmitting voice data among gateway(s). Each line requires 2 ports. For example, the 400 series gateway requires 8 UDP ports and the 800 series gateway requires 16 UDP ports. It is not necessary to change these, unless it conflicts with ports used by another device in your network.

For example, if the starting port is 9000, then Line 1 is using ports 9000 and 9001, and Line 2 is using ports 9002 and 9003, and so forth.

IP Configuration (Setting WAN Port)

There are three methods of obtaining a WAN IP address:

1.Static IP

2.DHCP, means a Dynamic IP (Cable Modem)

3.PPPoE (Dialup ADSL)

Using the DHCP and PPPoE for obtaining an IP address may vary. If you are not familiar with the network connection, please contact your local ISP.

20	SmartVoice Gateway(s) User Guide
	YML832 Rev2

Image 20

Contents Reference Guide Contents Important Note To ensure your Gateway complies with Australian StandardsIntroduction Product OverviewBroadband Service VoIP ServiceItems that you will need and things you will need to know Computer/NetworkAdvance Firewall and DoS Protection NetComm SmartVoice Gateway FeaturesVoice Features Configuration & Maintenance Network General SpecificationsFeatures are only available in models which have FXO ports SmartVoice Gateways User Guide YML832 Rev2 Restore the Gateway Rear Panel all modelsInstallation and Applications Connecting your SmartVoice GatewaysNetwork requirements Network ConnectionsGateway Assigned with a Public IP Address Gateway behind a NAT/Firewall Network RequirementsStun client Needs to be set up as either in static IP, DHCP, or PPPoE Telephone Connection Integrating the SmartVoice Gateway with PBX Integrating the SmartVoice Gateway with PBX Integrating the SmartVoice Gateway with PBX Configuring the Gateway via WEB Browser InstructionsNetwork Settings IP Configuration Setting WAN PortSetting Dynamic IP Dhcp DNS Settings Clone MACLAN interface mode Network Settings LANQoS Settings WAN QoSNAT/DDNS NAT Traversal Ddns ExampleTelephony Settings Prefix Number RulesFXO Line VoIP call in options Hotline FunctionsDescription SIP Settings 164 SmartVoice Gateways User Guide FXS/ FXO Representative number registers to Proxy Each line registers to Proxy independentlyServer Settings Private NetworkPrivate Network Numbers Calling Features Calling Feature InstructionsAdvanced Options Payload Type payload type of RFC2833 Line Settings Flash TimeCodec Settings Fax Settings Drop Inactive Call Digit Map Phone Book Speed Dial Caller Filter Transit Call Control Dialing principle to enable PIN code Gateway a PIN Code * Gateway B NumberLong-Distance Control Table Long Distance Exception TableCPT parameters Table CPT/Cadence SettingsBusy Tone Cadence Measurement CPT Auto Detect Direct Connection to Pstn SmartVoice Gateways User Guide YML832 Rev2 Connected to a PBX Extension Line 36008914 Save Settings Filling in the CPT TableCurrent Status and System Information RTP Packet Summary Stun Inquiry Ping Test Port Filtering IP Filtering MAC Filtering Virtual Server DMZ URL Filter Special Applications DoS Prevention Settings Enable Source IP Blocking Block the IP Backup and Restore Configuration NTP Network Time ProtocolProvision Settings System Operations Save Settings Software Upgrade Logout Preparation Configuring the Gateway via IVRConfiguration Methods IVR Interactive Voice Response Inquire Current Gateway’s WAN Port IP addressIVR Functions Table DNS IP address Set/QuerySet/Query Gateway Telephone Number Representative Number IP Configuration Settings WAN port Static IP Settings Adsl PPPoE SettingsPPPoE Account Settings PPPoE Password SettingSave Settings and Restart Select PPPoEPPPoE Character Conversion Table Dialed Number Processing Flow Dialing and dialed number routing principleInstruction End Appendix a Glossary 10BASE-TDNS Http NAT TCP VSP Appendix B Cable Information RJ-45 Network PortsCross-Over Cabling Straight and crossover cable configurationStraight-Through Cabling Appendix C Registration and Warranty Information Contact InformationProduct Warranty PO Box 1200, Lane Cove NSW 2066 Australia