NetComm Gateway Series manual Telephony Settings, Prefix Number Rules

Page 27

Telephony Settings

Prefix Number Rules

•Trunk Dial Out Verify/ Trunk Dial Out Replace: The system will transfer the number for all transit

out calls through the FXO port. For example: If you transit out with 01907123456, the system will replace it with 190601 907123456. If you transit out with 008621123456 the system will replace it with 190200 8621123456.

•Trunk Dial Out Deny: The system will deny the call with the leading number filled in this column.

NOTE: This rule only applies to transit out calls of gateway FXO ports.

•FXS Caller ID Generation: Select this option to enable the caller ID display function on FXS ports. FSK is used for Australian caller ID standards.

•FXO Caller ID Detection: Used to detect the Caller ID delivered from the PSTN to the FXO port. When enabled, the Caller ID detected on the FXO port will be sent to the SIP Proxy Server on transit in (dialing out) calls.

•Detection Level: If FXO can’t detect Caller ID, try to adjust it until it can.

NOTE: You have to enable “Wait for Caller ID before FXO / Trunk pick up” to ensure Caller ID is detected correctly.

•FSK Caller ID Type: Bellcore is used in Australia caller ID standards.

•Anonymous Caller ID (CLIR): When enabled, the gateway will use “anonymous” as caller identification to place calls.

•Anonymous Transit in W/O Caller ID: When enabled, if the FXO can detect caller ID in calls from PSTN, the gateway will use the detected caller ID as caller identification for transit in calls; if FXO cannot detect caller ID, the gateway will use “anonymous” as caller identification for transit in calls. When it not checked, if the FXO can detect caller ID in calls from PSTN, the gateway will use the detected caller ID as caller identification for transit in calls; if FXO cannot detect caller ID, the gateway will use its port phone number as caller identification for transit in calls.

•Trunk Incoming Prompt Voice: Select the greeting (must use the IVR 132 function to record a voice file) when FXO receives an inbound call (transit in).

•FXO Hunting VoIP call in option:

Caller Indicate Dial-Out:When users make calls to FXO ports from Internet, they will be required to dial a PSTN number after the calls connects to FXO port.

Default Dial-Out:When users make calls to FXO ports from Internet, the gateway will dial to PSTN with the number filled in “FXO Hunting Default Dial-Out”.

SmartVoice Gateway(s) User Guide

7

YML832 Rev2

 

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Reference Guide Contents To ensure your Gateway complies with Australian Standards Important NoteProduct Overview IntroductionComputer/Network Broadband ServiceVoIP Service Items that you will need and things you will need to knowNetComm SmartVoice Gateway Features Voice FeaturesAdvance Firewall and DoS Protection Configuration & Maintenance General Specifications Features are only available in models which have FXO portsNetwork SmartVoice Gateways User Guide YML832 Rev2 Rear Panel all models Restore the GatewayConnecting your SmartVoice Gateways Installation and ApplicationsNetwork Connections Gateway Assigned with a Public IP AddressNetwork requirements Requirements Gateway behind a NAT/Firewall NetworkStun client Needs to be set up as either in static IP, DHCP, or PPPoE Integrating the SmartVoice Gateway with PBX Telephone ConnectionIntegrating the SmartVoice Gateway with PBX Integrating the SmartVoice Gateway with PBX Instructions Configuring the Gateway via WEB BrowserIP Configuration Setting WAN Port Network SettingsSetting Dynamic IP Dhcp Clone MAC DNS SettingsNetwork Settings LAN LAN interface modeWAN QoS QoS SettingsNAT/DDNS NAT Traversal Example DdnsPrefix Number Rules Telephony SettingsHotline Functions FXO Line VoIP call in optionsDescription SIP Settings 164 SmartVoice Gateways User Guide Each line registers to Proxy independently FXS/ FXO Representative number registers to ProxyPrivate Network Server SettingsPrivate Network Numbers Calling Feature Instructions Calling FeaturesAdvanced Options Payload Type payload type of RFC2833 Flash Time Line SettingsCodec Settings Fax Settings Drop Inactive Call Digit Map Phone Book Speed Dial Caller Filter Transit Call Control Gateway a PIN Code * Gateway B Number Dialing principle to enable PIN codeLong Distance Exception Table Long-Distance Control TableCPT/Cadence Settings Busy Tone Cadence MeasurementCPT parameters Table CPT Auto Detect Direct Connection to Pstn SmartVoice Gateways User Guide YML832 Rev2 Connected to a PBX Extension Line 36008914 Filling in the CPT Table Save SettingsCurrent Status and System Information RTP Packet Summary Stun Inquiry Ping Test Port Filtering IP Filtering MAC Filtering Virtual Server DMZ URL Filter Special Applications DoS Prevention Settings Enable Source IP Blocking Block the IP NTP Network Time Protocol Backup and Restore ConfigurationProvision Settings System Operations Save Settings Software Upgrade Logout Configuring the Gateway via IVR Configuration MethodsPreparation Inquire Current Gateway’s WAN Port IP address IVR Interactive Voice ResponseDNS IP address Set/Query IVR Functions TableSet/Query Gateway Telephone Number Representative Number Adsl PPPoE Settings IP Configuration Settings WAN port Static IP SettingsSelect PPPoE PPPoE Account SettingsPPPoE Password Setting Save Settings and RestartPPPoE Character Conversion Table Dialing and dialed number routing principle InstructionDialed Number Processing Flow End 10BASE-T Appendix a GlossaryDNS Http NAT TCP VSP RJ-45 Network Ports Appendix B Cable InformationStraight and crossover cable configuration Straight-Through CablingCross-Over Cabling Contact Information Appendix C Registration and Warranty InformationProduct Warranty PO Box 1200, Lane Cove NSW 2066 Australia
Top Page Image Contents