Murphy CE-05171N manual Hardware Installation and Wiring, Mounting the Centurion Controller

Page 11

5.0Hardware Installation and Wiring

5.1Mounting the Centurion Controller

The Centurion can be mounted vertically or horizontally on a standard DIN rail. Three clamp type feet along the bottom of the controller attach to the DIN rail, however, rail stops are recommended to prevent sliding.

MOUNTING

BRACKET DETAIL

C3-1 Mounting

Bracket

DIN Type	C3-1
Mounting Rail

To Panel

2-1/2 in.

(64 mm)

13-1/8 in. (333 mm)

4-7/8 in.

(125 mm)

5.2 Mounting the Centurion C3-3 Display

The Centurion C3-3 Display can be mounted in the same hole cutout of other Murphy display modules. Four screws attached the display bezel to the mounting surface.

6-1/2 in. (165 mm)

6-1/2 in.

(165 mm)

2-1/8 in. (54 mm)

5-1/4 in.

(134 mm)

6.0 in. (152 mm)

5.50 in.

(140 mm)

3 in. (76 mm) 0.156 in. (4 mm) dia. 4 places

5.3Power Supply Wiring Power

Centurion C3-1 I/O Module

Requirements: (10 to 32) VDC: 30W (Max)

Power Hook Up

C3-1

There are two screw terminal connectors for power hookup at terminals 62 and 63, labeled B+ and B- respectively.

Centurion C3-2 Optional Expansion Module

Requirements: (10 to 32) VDC

There are three screw terminal connectors for power hookup at terminals 134 to 136, labeled B+, B- and B- respectively.

Power Hook Up

C3-2

TTD-98055N page 11 of 44

Image 11

Contents Centuriontm Warranty Table of Contents Communications Optional Components Basic Components and Key Features of the C3TM SeriesOverview Digital Inputs DI Input/Output TypesThermocouple Inputs TC Analog Inputs AIDigital Outputs do Magnetic Pickup MPUC3-1-A Analog Outputs AO Hazardous Area OperationMounting the Centurion C3-3 Display Hardware Installation and WiringPower Supply Wiring Power Centurion C3-1 I/O Module Mounting the Centurion ControllerWiring the Centurion C3-3 Display Wiring the Centurion C3-1/C3-2 TTD-98055N page 14 Features Fn Function Key Home ESC ACKRUN Stop RUN/STOP Test Status Area Operational/Process Information AreaController Version Mconfig PRO VEROperational Screens Display VERShutdown History Panel ESD Event History Panel ESD Panel Reset LOW Suct PressDISC. Temperature Cooler TemperatureVDC Battery ENG SpeedAmbient Temperature OIL PRS WTR Temp PSIENTER-ACCEPT ESC-CANCEL Setup Screens and MenusEnter Password Digital Input Digital Outputs SetupAnalog Inputs Setup Digital InputsESC Exit this Menu Analog Input 1 Setup ScreenAnalog Outputs Setup ANOUT01 ENTER-SUBMENU More Menus Analog Output 1 Setup ScreenThermocouple Thermocouple SetupThermocouple 1 Setup Type Offset Thermocouple 1 Setup Thermocouple OffsetMore Menu General Timer SetupGeneral Timer Setup Screen 00060RESET-RESET Timer ESC-EXIT this Menu Maintenance Timer SetupMaintenance Timer Setup Screen Maintenance Timer Setup Time Remaining Change OILControl Output Throttle ENTER-MENU More Menu Setpoints Setup ENTER-SUBMENU More MenusSetpoints Setup LO Suct PRS Control Output 1 Setup00004 PID Setup ENTER-SUBMENU More MenusPID Setup Screen PID 1 Setup ScreenPort Response Delay Port 1 Baud Rate Lube NO-FLOW Status Cycle TIME-INPUT # Prev NO-FLOW Input # 1 Setup Cycle Time SEC Total CyclesCycle Timer SEC More Menus Super User Menu Screen 28%YES Digital Input Status =CLOSED Diagnostico-Digital Inputs ScreenAnalog Output Status AI 1 ENG Speed Must be in Test Mode ESC-CANCELSuction PID ESC-EXIT PID Diagnostics ENTER-SUBMENU More MenusCommunication Status Modbus Register ENTER-EDIT More MenusCommunication Ports Remote Mode Commands Reset and RUN/STOPCommunications Additional Navigational AidsPort 2 USB Firmware Download Screen Firmware Update Mode Power and COM Link Must be MaintainedComm Fail Screen Invalid Configuration Press Setup to Access Download MenuConfiguration Fault Screen Modbus Protocol Terminal Emulator GlossaryBack Panel LED Description AppendicesHow To Order