Murphy CE-05171N ESC Exit this Menu, Analog Input 1 Setup Screen, Analog Output 1 Setup Screen

Page 25

C	TM

ANALOG INPUT 1 SETUP
___________________________________
MOVING AVERAGE SAMPLES	▼
RAW COUNT OFFSET

RAW COUNT SPAN

MINIMUM

MAXIMUM

___________________________________

(1,2,OR 4)	1	▼
___________________________________
▼▲	ENTER-EDIT

ESC EXIT THIS MENU

Analog Input 1 Setup Screen

	C	TM
	C
	ANALOG INPUT 1 SETUP
	MOVING AVERAGE SAMPLES	▼
	RAW COUNT OFFSET
	RAW COUNT SPAN
	MINIMUM

MAXIMUM

___________________________________

(1,2,OR 4)	1	▼
___________________________________
	–
▼▲	ENTER-ACCEPT
▼ ▼	ESC-CANCEL

Analog Input 1 Setup Screen

6.3.5 Analog Output

C TM

ANALOG OUTPUTS SETUP
ANALOG OUTPUT 1		▼
ANALOG OUTPUT 2
ANALOG OUTPUT 3
ANALOG OUTPUT 4
ANALOG OUTPUT 5
___________________________________
AN_OUT_01		▼
___________________________________
▼▲	ENTER-SUBMENU
▼▼	MORE MENUS

	Analog Output Setup Screen
	C	TM

ANALOG OUTPUTS 1 SETUP
RAW COUNT OFFSET		▼
RAW COUNT SPAN

MINIMUM

MAXIMUM

___________________________________

00000 ▼

___________________________________

▼▲ENTER-EDIT ESC-EXIT THIS MENU

Analog Output 1 Setup Screen

User may edit:

a)Raw Count Offset, the lowest reading expected from the device.

b)Determine Raw Count Span, the span from the lowest to highest reading expected from the device.

c)Apply the appropriate Minimum engineering scale. In most cases, 0% addresses a typical application and it is the Centurion’s default value.

d)Apply the appropriate Maximum engineering scale.

In most cases, 100% addresses a typical application and it is the Centurion’s default value.

CE-05171N page 25 of 44

Image 25

Contents Centuriontm Warranty Table of Contents Communications Overview Basic Components and Key Features of the C3TM SeriesOptional Components Digital Inputs DI Input/Output TypesThermocouple Inputs TC Analog Inputs AIDigital Outputs do Magnetic Pickup MPUC3-1-A Analog Outputs AO Hazardous Area OperationPower Supply Wiring Power Centurion C3-1 I/O Module Hardware Installation and WiringMounting the Centurion Controller Mounting the Centurion C3-3 DisplayWiring the Centurion C3-3 Display Wiring the Centurion C3-1/C3-2 TTD-98055N page 14 Features Fn Function Key Home ESC ACKRUN Stop RUN/STOP Test Status Area Operational/Process Information AreaOperational Screens Mconfig PRO VERDisplay VER Controller VersionDISC. Temperature Event History Panel ESD Panel Reset LOW Suct PressCooler Temperature Shutdown History Panel ESDAmbient Temperature Battery ENG SpeedOIL PRS WTR Temp PSI VDCEnter Password Setup Screens and MenusENTER-ACCEPT ESC-CANCEL Analog Inputs Setup Digital Outputs SetupDigital Inputs Digital InputAnalog Outputs Setup ANOUT01 ENTER-SUBMENU More Menus Analog Input 1 Setup ScreenAnalog Output 1 Setup Screen ESC Exit this MenuThermocouple 1 Setup Type Offset Thermocouple SetupThermocouple 1 Setup Thermocouple Offset ThermocoupleGeneral Timer Setup Screen General Timer Setup00060 More MenuMaintenance Timer Setup Screen Maintenance Timer SetupMaintenance Timer Setup Time Remaining Change OIL RESET-RESET Timer ESC-EXIT this MenuSetpoints Setup LO Suct PRS Setpoints Setup ENTER-SUBMENU More MenusControl Output 1 Setup Control Output Throttle ENTER-MENU More MenuPID Setup Screen PID Setup ENTER-SUBMENU More MenusPID 1 Setup Screen 00004Port Response Delay Port 1 Baud Rate Cycle Timer SEC More Menus NO-FLOW Input # 1 Setup Cycle Time SEC Total CyclesLube NO-FLOW Status Cycle TIME-INPUT # Prev YES 28%Super User Menu Screen Digital Input Status =CLOSED Diagnostico-Digital Inputs ScreenAnalog Output Status AI 1 ENG Speed Must be in Test Mode ESC-CANCELCommunication Status Modbus Register PID Diagnostics ENTER-SUBMENU More MenusENTER-EDIT More Menus Suction PID ESC-EXITCommunications Remote Mode Commands Reset and RUN/STOPAdditional Navigational Aids Communication PortsPort 2 USB Firmware Download Screen Firmware Update Mode Power and COM Link Must be MaintainedConfiguration Fault Screen Invalid Configuration Press Setup to Access Download MenuComm Fail Screen Modbus Protocol Terminal Emulator GlossaryBack Panel LED Description AppendicesHow To Order