Murphy CE-05171N manual Firmware Update Mode Power and COM Link Must be Maintained

Page 39

7.2.3 Downloading Configurations Via MConfigPro Software

The Centurion makes it easy for a user to download a configuration through the MConfigPro software.

1.From the Options menu of the MConfigPro software, choose the Options tab to identify the ports that the users PC can detect, and select the appropriate port that the user’s PC will use to communicate with the C3-3 Display or Centurion controller. Set the individual port parameters.

2.Through the Tools menu the user may choose to upload, or download as needed.

7.2.4Pass Through

During boot loader, the Centurion controller allows users to remain connected to both the PC and the C3-3 Display and update the two devices with a single connection.

During a download from the MConfigPro software, the user downloads to the C3-3 Display without entering boot loader mode and upon transferring the message, the Centurion controller is directed to accept the mes- sage through one port (Port 2) and pass it through another port (Port 1) directly to the C3-3 Display, as if the PC and C3-3 Display were directly connected.

7.2.5 Downloading Firmware Updates to the C3-3 Display

C TM

FIRMWARE UPDATE MODE

POWER AND COM LINK

MUST BE MAINTAINED

Firmware Download Screen

Firmware updates for the C3-3 Display require a USB con- nection. While boot loader mode for the display is not required for configuration downloads, it is required for firmware updates.

The bootloader can be entered by menu selection if the USB cable is currently connected, otherwise the C3-3 Display will reset and restart the current application firmware. Optionally, the bootloader can be entered by connecting the USB cable and cycling power. (This method will leave the display blank while in the bootloader.)

Upon entry to the bootloader, all communication to the con- troller will stop. There is a red status LED below the USB con- nector that will blink three times and then remain on while the bootloader is active.

While a file is being transferred, the Com 2 transmit LED will appear to be lit continuously. A successful download should complete in approximately five minutes.

Special 35 Jump Code

C3-3 Display allows a “Download Only” password that will allow access to the download menu. The password is set to a fixed value of 35. Once at the Download Only screen on the C3-3 Display, the user will select to download a firmware update.

Super User Menu

Super users will use the super user menu to download firmware updates.

All normal communication with the controller is stopped while in download mode.

The display will indicate the transfer is complete by displaying 100%.

CE-05171N page 39 of 44

Image 39
Contents Centuriontm Warranty Table of Contents Communications Basic Components and Key Features of the C3TM Series OverviewOptional Components Digital Inputs DI Input/Output TypesThermocouple Inputs TC Analog Inputs AIDigital Outputs do Magnetic Pickup MPUC3-1-A Analog Outputs AO Hazardous Area OperationMounting the Centurion C3-3 Display Hardware Installation and WiringPower Supply Wiring Power Centurion C3-1 I/O Module Mounting the Centurion ControllerWiring the Centurion C3-3 Display Wiring the Centurion C3-1/C3-2 TTD-98055N page 14 Features Fn Function Key Home ESC ACKRUN Stop RUN/STOP Test Status Area Operational/Process Information AreaController Version Mconfig PRO VEROperational Screens Display VERShutdown History Panel ESD Event History Panel ESD Panel Reset LOW Suct PressDISC. Temperature Cooler TemperatureVDC Battery ENG SpeedAmbient Temperature OIL PRS WTR Temp PSISetup Screens and Menus Enter PasswordENTER-ACCEPT ESC-CANCEL Digital Input Digital Outputs SetupAnalog Inputs Setup Digital InputsESC Exit this Menu Analog Input 1 Setup ScreenAnalog Outputs Setup ANOUT01 ENTER-SUBMENU More Menus Analog Output 1 Setup ScreenThermocouple Thermocouple SetupThermocouple 1 Setup Type Offset Thermocouple 1 Setup Thermocouple OffsetMore Menu General Timer SetupGeneral Timer Setup Screen 00060RESET-RESET Timer ESC-EXIT this Menu Maintenance Timer SetupMaintenance Timer Setup Screen Maintenance Timer Setup Time Remaining Change OILControl Output Throttle ENTER-MENU More Menu Setpoints Setup ENTER-SUBMENU More MenusSetpoints Setup LO Suct PRS Control Output 1 Setup00004 PID Setup ENTER-SUBMENU More MenusPID Setup Screen PID 1 Setup ScreenPort Response Delay Port 1 Baud Rate NO-FLOW Input # 1 Setup Cycle Time SEC Total Cycles Cycle Timer SEC More MenusLube NO-FLOW Status Cycle TIME-INPUT # Prev 28% YESSuper User Menu Screen Digital Input Status =CLOSED Diagnostico-Digital Inputs ScreenAnalog Output Status AI 1 ENG Speed Must be in Test Mode ESC-CANCELSuction PID ESC-EXIT PID Diagnostics ENTER-SUBMENU More MenusCommunication Status Modbus Register ENTER-EDIT More MenusCommunication Ports Remote Mode Commands Reset and RUN/STOPCommunications Additional Navigational AidsPort 2 USB Firmware Download Screen Firmware Update Mode Power and COM Link Must be MaintainedInvalid Configuration Press Setup to Access Download Menu Configuration Fault ScreenComm Fail Screen Modbus Protocol Terminal Emulator GlossaryBack Panel LED Description AppendicesHow To Order