Murphy CE-05171N manual Thermocouple Setup, Thermocouple 1 Setup Type Offset

Page 26

C TM

ANALOG OUTPUTS 1 SETUP

RAW COUNT OFFSET

RAW COUNT SPAN

MINIMUM

MAXIMUM

▼

___________________________________

00000 ▼

___________________________________

▼▲	ENTER-ACCEPT
▼ ▼	ESC-CANCEL

Analog Output 1 Setup Screen 1

6.3.6 Thermocouple Input

C	TM

THERMOCOUPLE SETUP

___________________________________

THERMOCOUPLE 1		▼
THERMOCOUPLE 2
THERMOCOUPLE	3
THERMOCOUPLE	4

THERMOCOUPLE 5

___________________________________

TC1	▼
___________________________________
▼▲	ENTER-SUBMENU
▼ ▼	MOORE MENUS

Thermocouple Setup Screen

C

TM

THERMOCOUPLE 1 SETUP

___________________________________

THERMOCOUPLE	TYPE	▼
THERMOCOUPLE	OFFSET

___________________________________

(J OR K)	J	▼
___________________________________
▼▲	ENTER-EDIT
ESC-EXIT THIS MENU

Thermocouple 1 Setup Screen

C TM

THERMOCOUPLE 1 SETUP

___________________________________

THERMOCOUPLE OFFSET

▼

___________________________________

	- 00015	▼
___________________________________
▼▲	ENTER-ACCEPT
▼▼	ESC-CANCEL

User may:

a)Identify whether the calibration Type should be set to J or K.

b)Assign the Offset value.

Thermocouple 1 Setup Screen 1

CE-05171N page 26 of 44

Image 26

Contents Centuriontm Warranty Table of Contents Communications Optional Components Basic Components and Key Features of the C3TM SeriesOverview Input/Output Types Digital Inputs DIAnalog Inputs AI Thermocouple Inputs TCMagnetic Pickup MPU Digital Outputs doC3-1-A Hazardous Area Operation Analog Outputs AOMounting the Centurion Controller Hardware Installation and WiringPower Supply Wiring Power Centurion C3-1 I/O Module Mounting the Centurion C3-3 DisplayWiring the Centurion C3-3 Display Wiring the Centurion C3-1/C3-2 TTD-98055N page 14 Features Home ESC ACK Fn Function KeyRUN Stop RUN/STOP Test Operational/Process Information Area Status AreaDisplay VER Mconfig PRO VEROperational Screens Controller VersionCooler Temperature Event History Panel ESD Panel Reset LOW Suct PressDISC. Temperature Shutdown History Panel ESDOIL PRS WTR Temp PSI Battery ENG SpeedAmbient Temperature VDCENTER-ACCEPT ESC-CANCEL Setup Screens and MenusEnter Password Digital Inputs Digital Outputs SetupAnalog Inputs Setup Digital InputAnalog Output 1 Setup Screen Analog Input 1 Setup ScreenAnalog Outputs Setup ANOUT01 ENTER-SUBMENU More Menus ESC Exit this MenuThermocouple 1 Setup Thermocouple Offset Thermocouple SetupThermocouple 1 Setup Type Offset Thermocouple00060 General Timer SetupGeneral Timer Setup Screen More MenuMaintenance Timer Setup Time Remaining Change OIL Maintenance Timer SetupMaintenance Timer Setup Screen RESET-RESET Timer ESC-EXIT this MenuControl Output 1 Setup Setpoints Setup ENTER-SUBMENU More MenusSetpoints Setup LO Suct PRS Control Output Throttle ENTER-MENU More MenuPID 1 Setup Screen PID Setup ENTER-SUBMENU More MenusPID Setup Screen 00004Port Response Delay Port 1 Baud Rate Lube NO-FLOW Status Cycle TIME-INPUT # Prev NO-FLOW Input # 1 Setup Cycle Time SEC Total CyclesCycle Timer SEC More Menus Super User Menu Screen 28%YES Diagnostico-Digital Inputs Screen Digital Input Status =CLOSEDMust be in Test Mode ESC-CANCEL Analog Output Status AI 1 ENG SpeedENTER-EDIT More Menus PID Diagnostics ENTER-SUBMENU More MenusCommunication Status Modbus Register Suction PID ESC-EXITAdditional Navigational Aids Remote Mode Commands Reset and RUN/STOPCommunications Communication PortsPort 2 USB Firmware Update Mode Power and COM Link Must be Maintained Firmware Download ScreenComm Fail Screen Invalid Configuration Press Setup to Access Download MenuConfiguration Fault Screen Modbus Protocol Glossary Terminal EmulatorAppendices Back Panel LED DescriptionHow To Order