MicroNet Technology SP5052, SP5050, SP5054 user manual Reboot command, Flash command

Page 19

Open debug message will show up specific information while VoIP FXO gateway is in operation. After executing the debug command, it should execute command debug -openas well. One example is demonstrated below.

usr/config$ debug -add h323 vp usr/config$ debug -open

Parameters Usage:

-status	Display the enabled debug flags.
-add	Add debug flag.
	-- h323 : h323 related information
	-- vp : voice related information
-delete	Remove specified debug flag.
-open	Start to show debug messages.
-close	Stop showing debug messages.

5.4 [reboot] command

After commit command, type reboot to reload VoIP FXO gateway in new configuration. The procedure is as below:

usr/config$ reboot

Attached TCP/IP interface to cpm unit 0 Attaching interface lo0...done AC4804[0] is OK

AC4804[1] is OK AC4804[2] is OK Successful

Initialize OSS libraries...OK! open stack successful cmInitialize succeed!

GK mode selected.

login:

5.5 [flash] command

This command will clean the configuration stored in the flash rom and reboot VoIP FXO gateway in factory default setting.

Parameter Usage:

-clean clean all the user-defined value, and reboot VoIP FXO gateway in factory default mode.

Note:

It is recommended that use “flash –clean” after application firmware id upgraded.

19

Image 19

Contents User’s Manual Introduction Introduction Features and specificationGeneral Features Audio featureAppearance Management FeaturesBack panel GND Pin Name Dir DescriptionStart System Operating ProcedureTelephone Line Requirement IP Environment SettingHyper Terminal Setting System RequirementPage Page Gatekeeper Mode Initializing VoIP FXO Gateway SettingConfigure VoIP FXO gateway Password Usr/config$ h323 -mode Peer-to-Peer ModeUsr/config$ ifaddr -ip 10.1.1.1 -mask 255.2555.255.0 -gate Usr/config$ h323 -mode 0 -gk 10.2.2.2 -e164 -alias fxoFixed IP Address usr/config$ ifaddr -ipsharing 1 Usr/config$ pbook -add name TEST1 ip 10.1.1.1 e164Behind IP-Sharing Dynamic IP Address -usr/config$ ifaddr -ipsharing What is Disconnect Tone Disconnect Tone ConfigurationHow to configure disconnect tone on VoIP FXO gateway Examples how to configure Tone table Adjust Tone Table parameters manuallyThere are two ways to analyze the disconnect tone Adjust Input Tone Level Debug command Command listsHelp command Quit commandFlash command Reboot commandUsr/config$ debug -add h323 vp usr/config$ debug -open Ifaddr command Commit commandUsr/config$ time Current time is THU JAN 01 052923 Time commandPing command Usr/config$ ifaddr -sntp 1Greetrd command Exit exit this command Parameter Usages Pbook commandAutomatic sequence number as index Phonebook RulesPppoe Sysconf command$bureau Print LineToLine feature should be used together with$h323 -mode 1 peer-to-peer mode $sysconf -2nddial 1 2nddial on$bureau 192.168.4.184 Please refer to 5.21 bureau commandValue is set to enable all ports Usr/config$ sysconf -sendxcode 1 -access set1 14 h323 commandPage Usr/config$ gk Gatekeeper information and configuration Gk commandVoice command Display voice codec information and configuration Usr/config$ voice -nscng g723 Tos commandUsr/config$ voice -mindelay 90 -maxdelay 150 -optfacor Support command Tone commandGroup command Usr/config$ group -pattern 1 3 -e164 100 Bureau commandPage Rom command Prefix commandPage Passwd command Download Procedure Upgrade the VoIP FXO gatewayTFTP/FTP server Page Browse the IP Address which has predefined via RS-232 Appendix Web configurationInput the login name and password Network Interface Start configureH323 Information System Config Voice Setting For Advanced User Phone Pattern For Advanced User Page Phone Book For Peer-to-Peer mode only Type Of Service Hot Lines PPPoE Password ROM Upgrade Flash Clean Commit Data Reboot System