MicroNet Technology SP5050, SP5052 LineToLine feature should be used together with, $bureau Print

Page 27

-idto

 

The duration of two pressed digits in dial mode

-eod

 

Digit type of end of dialing. ( 0:No end of dialing, 1:[*]

button,

 

2:[#] button )

 

 

-seizure

 

Choose line seizure mode (None/UCD).

-2nddial

 

Config GW to accept 2nd dtmf set. In this mode, device

 

 

from IP side needs to dial GW's E164, wait for PSTN

 

 

dialtone, and then dial out.

-drule

 

Specify digits to be filtered/dropped/inserted before

 

 

making an outgoing IP call or after receving an incoming

 

 

IP call.

-askpin

 

PIN code prompt before greeting.

 

 

0:Disable 1:Per Unit 2:Per Channel.

-ring

Ring number before answer.

 

 

0:Disable, other is number of ring ( 1 ~ 5 ).

-callalive

 

Enable or disable auto-disconnection after 10 seconds

-keypad

 

DTMF setting: 0=In-band, 1=H.245 Alphanumeric,

 

 

2=H.245 SignalType, 3=Q.931 UserInfo. , 4=RFC2833.

-pincode

 

Specify 6 of PIN codes.

-sendxcode

Send access code after connection.

 

 

0:Disable 1:Enable.

-access

 

Specify access codes.

Note:

Use character 'x' to delete the drule parameter. For line seizure 0: None, 1: UCD.

For askpin: f=0: No, f=1: Yes.

Direct in line feature should be used together with: $sysconf –2nddial 0 (2nddila off)

$h323 –mode 0 (Gatekeeper mode)

$bureau –print

for Direct in line table configuration

Hotline feature should be used together with:

$sysconf -2nddial 0 (2nddial off)

$h323 -mode 1

(peer-to-peer mode)

$bureau

-print

for Hotline/LineToLine table configuration.

LineToLine feature should be used together with:

$sysconf -2nddial 1 (2nddial on)

$h323 -mode 1 (peer-to-peer mode)

$bureau

-print

for Hotline/LineToLine table configuration.

Example:

sysconf -service 0 -plan 4 -port 1 1 1 1 0 0 sysconf -callalive 0 -keypad 0

sysconf -2nddial 0 -drule out_filter 002 in_insert x in_drop 1 sysconf -askpin 1 -pincode set1 12345

sysconf -sendxcode 1 -access set1 12345#

-service 0 (Dial In Service): In Dial In Service, VoIP FXO gateway will pick up incoming calls from PSTN, play pre-recorded voice greeting or, and then have users to make a 2nd dial to destination.

27

Image 27
Contents User’s Manual Introduction Introduction Features and specificationGeneral Features Audio featureManagement Features AppearanceBack panel GND Pin Name Dir DescriptionStart System Operating ProcedureTelephone Line Requirement IP Environment SettingHyper Terminal Setting System RequirementPage Page Gatekeeper Mode Initializing VoIP FXO Gateway SettingConfigure VoIP FXO gateway Password Usr/config$ h323 -mode Peer-to-Peer ModeUsr/config$ ifaddr -ip 10.1.1.1 -mask 255.2555.255.0 -gate Usr/config$ h323 -mode 0 -gk 10.2.2.2 -e164 -alias fxoUsr/config$ pbook -add name TEST1 ip 10.1.1.1 e164 Fixed IP Address usr/config$ ifaddr -ipsharing 1Behind IP-Sharing Dynamic IP Address -usr/config$ ifaddr -ipsharing Disconnect Tone Configuration What is Disconnect ToneHow to configure disconnect tone on VoIP FXO gateway Adjust Tone Table parameters manually Examples how to configure Tone tableThere are two ways to analyze the disconnect tone Adjust Input Tone Level Debug command Command listsHelp command Quit commandReboot command Flash commandUsr/config$ debug -add h323 vp usr/config$ debug -open Ifaddr command Commit commandUsr/config$ time Current time is THU JAN 01 052923 Time commandPing command Usr/config$ ifaddr -sntp 1Greetrd command Exit exit this command Parameter Usages Pbook commandAutomatic sequence number as index Phonebook RulesPppoe Sysconf command$bureau Print LineToLine feature should be used together with$h323 -mode 1 peer-to-peer mode $sysconf -2nddial 1 2nddial on$bureau 192.168.4.184 Please refer to 5.21 bureau commandValue is set to enable all ports Usr/config$ sysconf -sendxcode 1 -access set1 14 h323 commandPage Usr/config$ gk Gatekeeper information and configuration Gk commandVoice command Display voice codec information and configuration Tos command Usr/config$ voice -nscng g723Usr/config$ voice -mindelay 90 -maxdelay 150 -optfacor Support command Tone commandGroup command Usr/config$ group -pattern 1 3 -e164 100 Bureau commandPage Rom command Prefix commandPage Passwd command Upgrade the VoIP FXO gateway Download ProcedureTFTP/FTP server Page Browse the IP Address which has predefined via RS-232 Appendix Web configurationInput the login name and password Network Interface Start configureH323 Information System Config Voice Setting For Advanced User Phone Pattern For Advanced User Page Phone Book For Peer-to-Peer mode only Type Of Service Hot Lines PPPoE Password ROM Upgrade Flash Clean Commit Data Reboot System