Lucent Technologies Network Access Module manual 1INA Module Front Panel

Page 19

INA Front Panel

Figure 1-1INA Module Front Panel

DS-1 status LEDs

C1 serial port

DIP switches system LED console port (C0)

network activity LED

Ethernet port (Ether 0)

Ethernet link LED Reboot button

T1/PRI port

DS-1 test jacks

1210-001

DIP Switches. DIP switch 1 controls the configuration of serial port C0. DIP switch 2 controls ComOS boot behavior. See “Set DIP Switches” on page 3-2.

System LED. This LED indicates the status of the routing hardware and the ComOS. One blink every 5 seconds indicates normal operation. See “System LED” on page 3-5.

C0 Serial Port. This RJ-45 connector is used to connect a PC or terminal to act as a console. The console is used to access the ComOS command line interface. See “Connect a Console (Optional)” on page 3-3.

Network Activity LED. This amber LED blinks to indicate network traffic. See “Ethernet LEDs” on page 3-6.

INA Module

1-3

Image 19

Contents Merlin Magix Year 2000 Compliance Your Responsibility for Your System’s SecurityCopyright and Trademarks Page Contents Using the INAWizard ContentsUsing the Command Line Interface Merlin Magix Administration Using PMVisionTroubleshooting Cable SpecificationsViii IndexImportant Safety Instructions -SAVE These Instructions Safety InstructionsImportant Safety Instructions -SAVE These Instructions Merlin Magix Documentation About This GuideAudience Related DocumentationMerlin Legend Superscript Communications System, Release Calling Group Supervisor and Service Observer User GuideSPM, Maintenance and Troubleshooting Related DocumentationAdditional References PortMaster DocumentationConvention Use Examples Bold font Document ConventionsDocument Advisories Document ConventionsUSA Dealers and Value-Added Resellers VARS. Call Limited WarrantyTechnical Support INA Module Training CoursesSubscribing to PortMaster Mailing Lists Xvi On the Merlin Magix INA AdministrationINA Module INA Module DescriptionINA Front Panel On the INA ModuleINA Front Panel INA Module 1INA Module Front PanelInstallation and Configuration Steps Installation and Configuration StepsCollect information about your T1 or PRI line T1/PRI Provisioning Getting Ready for ConfigurationSet Up T1/PRI on the Merlin Magix Setting ExampleNetwork Settings Network SettingsAssign T1/PRI Channels Settings Example 192.198.32.33 16172.26.131.37192.198.32.17 HoursConnect a Serial Passthrough Cable Installing the INA ModuleInstall the INA Module in a Carrier Connect CablesConnect Cables Set DIP SwitchesSet DIP switch 1 to the right Set DIP switch 2 to the leftConnect a Console Optional Installing the INA ModuleConnect a T1/PRI Cable Observe LED Behavior Connect an Ethernet CableObserve LED Behavior T1/PRI LEDsSystem LED System LED8Ethernet LEDs Ethernet LEDsOver a LAN Using the INAWizardInstall the Wizard Connect the Workstation to the INA ModuleRun the Wizard Using the C0 Console Port Using the Command Line InterfaceConnect a Console Log Using a Telnet SessionUsing the Passthrough Serial Connection Set the Administrative PasswordSet the IP Address and Netmask Command set password PasswordCommand set ether0 broadcast highlow Set the Ether0 Network AddressSet the System Name Set the Default Route GatewayCommand set sysname String Set the System NameSet the Domain Name Configure the WAN PortSet the Name Service Set the Name ServerSet the Channel Rate Set Up Additional WAN PortsSet the Port IP Address Optional Apply Filters to the WAN Port Optional Set the Destination IP AddressSet the Netmask Set the Transport ProtocolConfigure the WAN Port Install PMVision Using PMVisionRun PMVision Using a Crossover CableRun PMVision Communicate with the INA Module Using PMVisionCommunicate with the INA Module Selecting PMVision Functions Using Configuration FunctionsWorking with Configuration Panels Selecting PMVision FunctionsEdit Enter Basic SettingsWorking with Configuration Displays SaveName server address INA→ Configure→ Global Edit System name INA→ Configure→ SnmpDefault gateway INA→ Configure→ Global Name service type INA→ Configure→ GlobalBack Up the INA Module Settings Using the Backup and Restore Functions6PMVision Backup Dialog Restore the INA Module SettingsLED Behavior Possible Cause Solution Troubleshooting aObserving LED Behavior Observing Boot Messages Observing Boot MessagesAttach a console Observe the boot messages displayed on the console screen Press the reboot buttonAddress Error at failedField Possible Message Explanation Memory addressTable A-2Interpreting Diagnostic Boot Messages Using the DS-1 Test JacksTest Jack Label Description and Usage Using the DS-1 Test JacksFigure A-1DS-1 Test Jack Locations Using the DS-1 Test Jacks Console Cable Cable SpecificationsSignal Cables SpecifiedT1/PRI Cable Ethernet Connector Transmission Type Cable Type DistanceT1/PRI Cable Ethernet InterfaceCrossover Cable RJ-45 ConnectorCrossover Cable Crossover Cable INA Module Administration Options Merlin Magix AdministrationINAModule System Programming Summary Activate or Deactivate the Onboard CSU INA Module Administration OptionsDSU Channel Selection Selection Description INA Module Maintenance OptionsError Events INA Module Maintenance OptionsDescription INA ModuleMaintenance OptionsMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events Hour Event TotalsCurrent Events Clearing Error EventsMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ Current Menu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ ClearLine Loopback Test Menu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ LineLpbkMenu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ Demand TestsINA Module System Interactions Backup and RestoreSurrogate Operation Other System Interactions Pcmcia Flash Memory Card-Based Upgrade OperationBoard Renumbering Print ReportsSystem Restart ReplacementCondition Explanation System Erase Frigid StartINA Module System Interactions Index-1 IndexIndex-2 IndexIndex-3 Index-4 T1/PRIIndex-5