Lucent Technologies Network Access Module manual Demand Tests, Line Loopback Test

Page 66

INA Module Maintenance Options

Demand Tests

The INA module board incorporates three new demand tests:

•Line loopback

•Payload loopback

•Bit error rate test (BERT)

Line Loopback Test

The line loopback test loops the T1 signal back towards the network without regenerating framing and without recalculating a cyclic redundancy test (CRC) checksum. To perform this test, you must first busy out the INA module. From your system programming console, use the following sequence to start the line loopback test:

Menu: Maintenance→ Slot→ Slot#→ Enter→ Demand test→ LineLpbk

After the line loopback test has been started, selecting → Back terminates the test.

Note – During the line loopback test, the INA module transmit clocking is derived from the signal received by the INA module. The remote end of the T1 connection must be

set up as the clock master for the T1/PRI inrfco v(o)6.5il tilclooPayloadeLoopbackThe a4(sy)-729(l)-1.1(1) eern f75.4(r98.1amin)665n f75.4atenC rech(eck-7.5(c)-1.pref759(u).4ok0.3m)12-7.5rc .1tin.h

st fi(s)-.1 t yetyeIN(A)--5.4( )12.1mtdume. Flomt sst prsog ramtin o(n)-593(s)1.1ol(e)-8.4,ietye llow iu seuete sahep(a)-7.9ybll(a)-7.9d( lo1)-12.2pok1teest:

Menu: Maintenance→ Slot→ Slot#→ Enter→ Demand test→

C-6	INA Module Installation and Configuration Guide

Image 66

Contents Merlin Magix Your Responsibility for Your System’s Security Year 2000 ComplianceCopyright and Trademarks Page Contents Contents Using the INAWizardUsing the Command Line Interface Cable Specifications Using PMVisionTroubleshooting Merlin Magix AdministrationIndex ViiiSafety Instructions Important Safety Instructions -SAVE These InstructionsImportant Safety Instructions -SAVE These Instructions Related Documentation About This GuideAudience Merlin Magix DocumentationRelated Documentation Calling Group Supervisor and Service Observer User GuideSPM, Maintenance and Troubleshooting Merlin Legend Superscript Communications System, ReleasePortMaster Documentation Additional ReferencesDocument Conventions Document ConventionsDocument Advisories Convention Use Examples Bold fontINA Module Training Courses Limited WarrantyTechnical Support USA Dealers and Value-Added Resellers VARS. CallSubscribing to PortMaster Mailing Lists Xvi INA Module Description INA AdministrationINA Module On the Merlin MagixOn the INA Module INA Front PanelINA Front Panel 1INA Module Front Panel INA ModuleInstallation and Configuration Steps Installation and Configuration StepsCollect information about your T1 or PRI line Setting Example Getting Ready for ConfigurationSet Up T1/PRI on the Merlin Magix T1/PRI ProvisioningNetwork Settings Network SettingsAssign T1/PRI Channels Settings Example Hours 16172.26.131.37192.198.32.17 192.198.32.33Connect Cables Installing the INA ModuleInstall the INA Module in a Carrier Connect a Serial Passthrough CableSet DIP switch 2 to the left Set DIP SwitchesSet DIP switch 1 to the right Connect CablesInstalling the INA Module Connect a Console OptionalConnect a T1/PRI Cable T1/PRI LEDs Connect an Ethernet CableObserve LED Behavior Observe LED BehaviorSystem LED System LEDEthernet LEDs 8Ethernet LEDsConnect the Workstation to the INA Module Using the INAWizardInstall the Wizard Over a LANRun the Wizard Using the Command Line Interface Using the C0 Console PortConnect a Console Set the Administrative Password Using a Telnet SessionUsing the Passthrough Serial Connection LogSet the Ether0 Network Address Command set password PasswordCommand set ether0 broadcast highlow Set the IP Address and NetmaskSet the System Name Set the Default Route GatewayCommand set sysname String Set the System NameSet the Name Server Configure the WAN PortSet the Name Service Set the Domain NameSet Up Additional WAN Ports Set the Channel RateSet the Port IP Address Optional Set the Transport Protocol Set the Destination IP AddressSet the Netmask Apply Filters to the WAN Port OptionalConfigure the WAN Port Using PMVision Install PMVisionUsing a Crossover Cable Run PMVisionRun PMVision Using PMVision Communicate with the INA ModuleCommunicate with the INA Module Selecting PMVision Functions Using Configuration FunctionsWorking with Configuration Panels Selecting PMVision FunctionsSave Enter Basic SettingsWorking with Configuration Displays EditName service type INA→ Configure→ Global Edit System name INA→ Configure→ SnmpDefault gateway INA→ Configure→ Global Name server address INA→ Configure→ GlobalUsing the Backup and Restore Functions Back Up the INA Module SettingsRestore the INA Module Settings 6PMVision Backup DialogTroubleshooting a LED Behavior Possible Cause SolutionObserving LED Behavior Observing Boot Messages Observing Boot MessagesAttach a console Press the reboot button Observe the boot messages displayed on the console screenMemory address Error at failedField Possible Message Explanation AddressUsing the DS-1 Test Jacks Table A-2Interpreting Diagnostic Boot MessagesUsing the DS-1 Test Jacks Test Jack Label Description and UsageFigure A-1DS-1 Test Jack Locations Using the DS-1 Test Jacks Cables Specified Cable SpecificationsSignal Console CableEthernet Interface Ethernet Connector Transmission Type Cable Type DistanceT1/PRI Cable T1/PRI CableRJ-45 Connector Crossover CableCrossover Cable Crossover Cable Merlin Magix Administration INA Module Administration OptionsINAModule System Programming Summary INA Module Administration Options Activate or Deactivate the Onboard CSUDSU Channel Selection INA Module Maintenance Options INA Module Maintenance OptionsError Events Selection DescriptionHour Event Totals INA ModuleMaintenance OptionsMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events DescriptionMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ Clear Clearing Error EventsMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ Current Current EventsDemand Tests Menu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ LineLpbkMenu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ Line Loopback TestBackup and Restore INA Module System InteractionsSurrogate Operation Print Reports Pcmcia Flash Memory Card-Based Upgrade OperationBoard Renumbering Other System InteractionsFrigid Start ReplacementCondition Explanation System Erase System RestartINA Module System Interactions Index Index-1Index Index-2Index-3 T1/PRI Index-4Index-5