Lucent Technologies Network Access Module manual Set the Ether0 Network Address

Page 35

Set the Ether0 Network Address

Command> set password [Password]

Command> save all

Caution – Change the administrative password each time you give it to somone outside

!the organization for servicing.

Set the Ether0 Network Address

You can set an IP and IPX address on the INA module. Both IP and IPX routing protocols are enabled by default. Information on IPX settings can be found in the PortMaster Configuration Guide and the PortMaster Command Line Reference.

Set the IP Address and Netmask

The IP address identifies the port for IP Ethernet traffic. The default netmask (subnet mask) is 255.255.255.0. If your network is divided into subnets, enter the netmask that identifies how your network addresses are divided between the network portion and the host portion.

Use the following commands to set the IP address and netmask:

Command> set ether0 address Ipaddress

Command> set ether0 netmask Ipmask

Command> save all

Set the Broadcast Address

The broadcast address, constructed from the IP address and netmask of a specified Ethernet interface, is used by RIP to send information to other hosts on a local Ethernet network.

When you set a broadcast address for the Ethernet port on the INA module, all other hosts on the local Ethernet network, must be set to the same broadcast address.

Use these commands to set the broadcast address:

Command> set ether0 broadcast highlow

Command> save all

high—Use when the host part of the binary address is all 1s (ones)—such as 192.168.1.255. This is the most often used setting.

low—Use when the host part of the binary address is all 0s (zeros)—such as 192.168.1.0. This is the default setting.

Using the Command Line Interface

5-3

Image 35
Contents Merlin Magix Year 2000 Compliance Your Responsibility for Your System’s SecurityCopyright and Trademarks Page Contents Using the Command Line Interface ContentsUsing the INAWizard Merlin Magix Administration Using PMVisionTroubleshooting Cable SpecificationsViii IndexImportant Safety Instructions -SAVE These Instructions Safety InstructionsImportant Safety Instructions -SAVE These Instructions Merlin Magix Documentation About This GuideAudience Related DocumentationMerlin Legend Superscript Communications System, Release Calling Group Supervisor and Service Observer User GuideSPM, Maintenance and Troubleshooting Related DocumentationAdditional References PortMaster DocumentationConvention Use Examples Bold font Document ConventionsDocument Advisories Document ConventionsUSA Dealers and Value-Added Resellers VARS. Call Limited WarrantyTechnical Support INA Module Training CoursesSubscribing to PortMaster Mailing Lists Xvi On the Merlin Magix INA AdministrationINA Module INA Module DescriptionINA Front Panel On the INA ModuleINA Front Panel INA Module 1INA Module Front PanelCollect information about your T1 or PRI line Installation and Configuration StepsInstallation and Configuration Steps T1/PRI Provisioning Getting Ready for ConfigurationSet Up T1/PRI on the Merlin Magix Setting ExampleAssign T1/PRI Channels Network SettingsNetwork Settings Settings Example 192.198.32.33 16172.26.131.37192.198.32.17 HoursConnect a Serial Passthrough Cable Installing the INA ModuleInstall the INA Module in a Carrier Connect CablesConnect Cables Set DIP SwitchesSet DIP switch 1 to the right Set DIP switch 2 to the leftConnect a T1/PRI Cable Installing the INA ModuleConnect a Console Optional Observe LED Behavior Connect an Ethernet CableObserve LED Behavior T1/PRI LEDsSystem LED System LED8Ethernet LEDs Ethernet LEDsOver a LAN Using the INAWizardInstall the Wizard Connect the Workstation to the INA ModuleRun the Wizard Connect a Console Using the Command Line InterfaceUsing the C0 Console Port Log Using a Telnet SessionUsing the Passthrough Serial Connection Set the Administrative PasswordSet the IP Address and Netmask Command set password PasswordCommand set ether0 broadcast highlow Set the Ether0 Network AddressSet the System Name Set the Default Route GatewayCommand set sysname String Set the System NameSet the Domain Name Configure the WAN PortSet the Name Service Set the Name ServerSet the Port IP Address Optional Set Up Additional WAN PortsSet the Channel Rate Apply Filters to the WAN Port Optional Set the Destination IP AddressSet the Netmask Set the Transport ProtocolConfigure the WAN Port Install PMVision Using PMVisionRun PMVision Using a Crossover CableRun PMVision Communicate with the INA Module Using PMVisionCommunicate with the INA Module Selecting PMVision Functions Using Configuration FunctionsWorking with Configuration Panels Selecting PMVision FunctionsEdit Enter Basic SettingsWorking with Configuration Displays SaveName server address INA→ Configure→ Global Edit System name INA→ Configure→ SnmpDefault gateway INA→ Configure→ Global Name service type INA→ Configure→ GlobalBack Up the INA Module Settings Using the Backup and Restore Functions6PMVision Backup Dialog Restore the INA Module SettingsObserving LED Behavior Troubleshooting aLED Behavior Possible Cause Solution Attach a console Observing Boot MessagesObserving Boot Messages Observe the boot messages displayed on the console screen Press the reboot buttonAddress Error at failedField Possible Message Explanation Memory addressTable A-2Interpreting Diagnostic Boot Messages Using the DS-1 Test JacksTest Jack Label Description and Usage Using the DS-1 Test JacksFigure A-1DS-1 Test Jack Locations Using the DS-1 Test Jacks Console Cable Cable SpecificationsSignal Cables SpecifiedT1/PRI Cable Ethernet Connector Transmission Type Cable Type DistanceT1/PRI Cable Ethernet InterfaceCrossover Cable RJ-45 ConnectorCrossover Cable Crossover Cable INAModule System Programming Summary Merlin Magix AdministrationINA Module Administration Options DSU Channel Selection INA Module Administration OptionsActivate or Deactivate the Onboard CSU Selection Description INA Module Maintenance OptionsError Events INA Module Maintenance OptionsDescription INA ModuleMaintenance OptionsMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events Hour Event TotalsCurrent Events Clearing Error EventsMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ Current Menu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ ClearLine Loopback Test Menu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ LineLpbkMenu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ Demand TestsSurrogate Operation Backup and RestoreINA Module System Interactions Other System Interactions Pcmcia Flash Memory Card-Based Upgrade OperationBoard Renumbering Print ReportsSystem Restart ReplacementCondition Explanation System Erase Frigid StartINA Module System Interactions Index-1 IndexIndex-2 IndexIndex-3 Index-4 T1/PRIIndex-5