Lucent Technologies Network Access Module Edit System name INA→ Configure→ Snmp, Ports, Edit

Page 46

Selecting PMVision Functions

Table 6-1Basic INA Module Configuration Using PMVision (Continued)

Setting	Select PMVision Function:	Entry

Ether0 netmask	INA→ Configure→ Ethernets,	IP netmask
	Edit

System name	INA→ Configure→ SNMP	System		name

Default gateway	INA→ Configure→ Global	IP gateway

Name service type	INA→ Configure→ Global	Name	service

Name server address	INA→ Configure→ Global	Primary			name	server

WAN port address	INA→ Configure→ Ports, Sync	Local		IP	address
	ports, Edit

Remote router address	INA→ Configure→ Ports, Sync	DestinationIP
	ports, Edit	address

Remote router	INA→ Configure→ Ports, Sync	Netmask
netmask	ports, Edit

Channel rate	INA→ Configure→ Lines,	Rate,		Save
	line0,→ Edit→ Groups→ Edit

Protocol	INA→ Configure→ Ports, Sync	PPP	or	Frame
	ports, Edit

DLCI list source	INA→ Configure→ Ports, Sync	Keep	Alive
(Frame Relay only)	ports, Edit	LMI, Annex-D or
		LMI, Annex-D or
		manual

DLCI Keepalive Value	INA→ Configure→ Ports, Sync	Keepalive interval
(Frame Relay only)	ports, Edit

DLCI list (Frame Relay		DLCI	number,			IP
only)		address

DHCP server address	INA→ Configure→ DHCP	Select the checkbox
		to enable

DHCP lease time	INA→ Configure→ DHCP	Lease

DHCP static binding IP	INA→ Configure→ DHCP→	IP address,				MAC
addresses and	Bindings→ Add	address
corresponding MAC
addresses

DHCP address pool	INA→ Configure→ DHCP	IP pool			addresses
start address and end
address

6-6	INA Module Installation and Configuration Guide

Image 46

Contents Merlin Magix Your Responsibility for Your System’s Security Year 2000 ComplianceCopyright and Trademarks Page Contents Using the INAWizard ContentsUsing the Command Line Interface Cable Specifications Using PMVisionTroubleshooting Merlin Magix AdministrationIndex ViiiSafety Instructions Important Safety Instructions -SAVE These InstructionsImportant Safety Instructions -SAVE These Instructions Related Documentation About This GuideAudience Merlin Magix DocumentationRelated Documentation Calling Group Supervisor and Service Observer User GuideSPM, Maintenance and Troubleshooting Merlin Legend Superscript Communications System, ReleasePortMaster Documentation Additional ReferencesDocument Conventions Document ConventionsDocument Advisories Convention Use Examples Bold fontINA Module Training Courses Limited WarrantyTechnical Support USA Dealers and Value-Added Resellers VARS. CallSubscribing to PortMaster Mailing Lists Xvi INA Module Description INA AdministrationINA Module On the Merlin MagixINA Front Panel On the INA ModuleINA Front Panel 1INA Module Front Panel INA ModuleInstallation and Configuration Steps Installation and Configuration StepsCollect information about your T1 or PRI line Setting Example Getting Ready for ConfigurationSet Up T1/PRI on the Merlin Magix T1/PRI ProvisioningNetwork Settings Network SettingsAssign T1/PRI Channels Settings Example Hours 16172.26.131.37192.198.32.17 192.198.32.33Connect Cables Installing the INA ModuleInstall the INA Module in a Carrier Connect a Serial Passthrough CableSet DIP switch 2 to the left Set DIP SwitchesSet DIP switch 1 to the right Connect CablesConnect a Console Optional Installing the INA ModuleConnect a T1/PRI Cable T1/PRI LEDs Connect an Ethernet CableObserve LED Behavior Observe LED BehaviorSystem LED System LEDEthernet LEDs 8Ethernet LEDsConnect the Workstation to the INA Module Using the INAWizardInstall the Wizard Over a LANRun the Wizard Using the C0 Console Port Using the Command Line InterfaceConnect a Console Set the Administrative Password Using a Telnet SessionUsing the Passthrough Serial Connection LogSet the Ether0 Network Address Command set password PasswordCommand set ether0 broadcast highlow Set the IP Address and NetmaskSet the System Name Set the Default Route GatewayCommand set sysname String Set the System NameSet the Name Server Configure the WAN PortSet the Name Service Set the Domain NameSet the Channel Rate Set Up Additional WAN PortsSet the Port IP Address Optional Set the Transport Protocol Set the Destination IP AddressSet the Netmask Apply Filters to the WAN Port OptionalConfigure the WAN Port Using PMVision Install PMVisionRun PMVision Using a Crossover CableRun PMVision Communicate with the INA Module Using PMVision Communicate with the INA Module Selecting PMVision Functions Using Configuration FunctionsWorking with Configuration Panels Selecting PMVision FunctionsSave Enter Basic SettingsWorking with Configuration Displays EditName service type INA→ Configure→ Global Edit System name INA→ Configure→ SnmpDefault gateway INA→ Configure→ Global Name server address INA→ Configure→ GlobalUsing the Backup and Restore Functions Back Up the INA Module SettingsRestore the INA Module Settings 6PMVision Backup DialogLED Behavior Possible Cause Solution Troubleshooting aObserving LED Behavior Observing Boot Messages Observing Boot MessagesAttach a console Press the reboot button Observe the boot messages displayed on the console screenMemory address Error at failedField Possible Message Explanation AddressUsing the DS-1 Test Jacks Table A-2Interpreting Diagnostic Boot MessagesUsing the DS-1 Test Jacks Test Jack Label Description and UsageFigure A-1DS-1 Test Jack Locations Using the DS-1 Test Jacks Cables Specified Cable SpecificationsSignal Console CableEthernet Interface Ethernet Connector Transmission Type Cable Type DistanceT1/PRI Cable T1/PRI CableCrossover Cable RJ-45 ConnectorCrossover Cable Crossover Cable INA Module Administration Options Merlin Magix AdministrationINAModule System Programming Summary Activate or Deactivate the Onboard CSU INA Module Administration OptionsDSU Channel Selection INA Module Maintenance Options INA Module Maintenance OptionsError Events Selection DescriptionHour Event Totals INA ModuleMaintenance OptionsMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events DescriptionMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ Clear Clearing Error EventsMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ Current Current EventsDemand Tests Menu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ LineLpbkMenu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ Line Loopback TestINA Module System Interactions Backup and RestoreSurrogate Operation Print Reports Pcmcia Flash Memory Card-Based Upgrade OperationBoard Renumbering Other System InteractionsFrigid Start ReplacementCondition Explanation System Erase System RestartINA Module System Interactions Index Index-1Index Index-2Index-3 T1/PRI Index-4Index-5