Lucent Technologies Network Access Module manual Index-1

Page 71

Index

Numerics

100D module C-1 operation 2-2 renumbering boards C-8

24-hour event totals C-4

A

activate or deactivate CSU 2-1,C-2 administration options C-1 administrative password 5-2

B

B8ZS encoding 2-1,C-1 backup

INA module settings 6-7 MERLIN MAGIX settings C-7

BERT C-6

bipolar 8-zero substitution. See B8ZS bit error rate test (BERT) C-6 boards

renumbering C-8 replacement C-9

boot messages checking A-2 interpreting A-4

boot mode, configuring 3-3 BOOTP 3-3

broadcast address, setting 5-3

C

C0 port location 1-3 using 5-1

C1 serial port location 1-2

using for console session 5-2 cables

connecting 3-1 console 3-3,B-1 crossover B-3 Ethernet 3-4,B-2 passthrough 3-1

specifications B-1 T1/PRI 3-3,B-2

caution icon xiv

channel rate, setting 2-3,5-6,6-6 channels

assigning 2-2,C-2 setting 5-6

channel service unit. See CSU code supression, B8ZS 2-1,C-1 cold start C-9

command line interface description 1-2 using 5-1

configuration console port 3-2 getting information 2-1 parameters 2-3

steps 1-4

configuration displays, PMVision 6-5 configuration functions, PMVision 6-4 configuration panels, PMVision 6-4 connecting

console 3-3 Ethernet cable 3-4 INAWizard workstation 4-1 PMVision workstation 6-1 serial passthrough cable 3-1 T1/PRI Cable 3-3

console cable B-1

checking messages A-2 configuring port 3-2 connecting 3-3

console port. See C0 port console session console session

C1 serial port 5-2

passthrough serial connection 5-2 Telnet 5-2

using C0 port 5-1 contact information

Lucent technical support xv mailing lists xv

conventions in this guide xiv crossover cable

Index-1

Image 71
Contents Merlin Magix Year 2000 Compliance Your Responsibility for Your System’s SecurityCopyright and Trademarks Page Contents Using the Command Line Interface ContentsUsing the INAWizard Merlin Magix Administration Using PMVisionTroubleshooting Cable SpecificationsViii IndexImportant Safety Instructions -SAVE These Instructions Safety InstructionsImportant Safety Instructions -SAVE These Instructions Merlin Magix Documentation About This GuideAudience Related DocumentationMerlin Legend Superscript Communications System, Release Calling Group Supervisor and Service Observer User GuideSPM, Maintenance and Troubleshooting Related DocumentationAdditional References PortMaster DocumentationConvention Use Examples Bold font Document ConventionsDocument Advisories Document ConventionsUSA Dealers and Value-Added Resellers VARS. Call Limited WarrantyTechnical Support INA Module Training CoursesSubscribing to PortMaster Mailing Lists Xvi On the Merlin Magix INA AdministrationINA Module INA Module DescriptionINA Front Panel On the INA ModuleINA Front Panel INA Module 1INA Module Front PanelCollect information about your T1 or PRI line Installation and Configuration StepsInstallation and Configuration Steps T1/PRI Provisioning Getting Ready for ConfigurationSet Up T1/PRI on the Merlin Magix Setting ExampleAssign T1/PRI Channels Network SettingsNetwork Settings Settings Example 192.198.32.33 16172.26.131.37192.198.32.17 HoursConnect a Serial Passthrough Cable Installing the INA ModuleInstall the INA Module in a Carrier Connect CablesConnect Cables Set DIP SwitchesSet DIP switch 1 to the right Set DIP switch 2 to the leftConnect a T1/PRI Cable Installing the INA ModuleConnect a Console Optional Observe LED Behavior Connect an Ethernet CableObserve LED Behavior T1/PRI LEDsSystem LED System LED8Ethernet LEDs Ethernet LEDsOver a LAN Using the INAWizardInstall the Wizard Connect the Workstation to the INA ModuleRun the Wizard Connect a Console Using the Command Line InterfaceUsing the C0 Console Port Log Using a Telnet SessionUsing the Passthrough Serial Connection Set the Administrative PasswordSet the IP Address and Netmask Command set password PasswordCommand set ether0 broadcast highlow Set the Ether0 Network AddressSet the System Name Set the Default Route GatewayCommand set sysname String Set the System NameSet the Domain Name Configure the WAN PortSet the Name Service Set the Name ServerSet the Port IP Address Optional Set Up Additional WAN PortsSet the Channel Rate Apply Filters to the WAN Port Optional Set the Destination IP AddressSet the Netmask Set the Transport ProtocolConfigure the WAN Port Install PMVision Using PMVisionRun PMVision Using a Crossover CableRun PMVision Communicate with the INA Module Using PMVisionCommunicate with the INA Module Selecting PMVision Functions Using Configuration FunctionsWorking with Configuration Panels Selecting PMVision FunctionsEdit Enter Basic SettingsWorking with Configuration Displays SaveName server address INA→ Configure→ Global Edit System name INA→ Configure→ SnmpDefault gateway INA→ Configure→ Global Name service type INA→ Configure→ GlobalBack Up the INA Module Settings Using the Backup and Restore Functions6PMVision Backup Dialog Restore the INA Module SettingsObserving LED Behavior Troubleshooting aLED Behavior Possible Cause Solution Attach a console Observing Boot MessagesObserving Boot Messages Observe the boot messages displayed on the console screen Press the reboot buttonAddress Error at failedField Possible Message Explanation Memory addressTable A-2Interpreting Diagnostic Boot Messages Using the DS-1 Test JacksTest Jack Label Description and Usage Using the DS-1 Test JacksFigure A-1DS-1 Test Jack Locations Using the DS-1 Test Jacks Console Cable Cable SpecificationsSignal Cables SpecifiedT1/PRI Cable Ethernet Connector Transmission Type Cable Type DistanceT1/PRI Cable Ethernet InterfaceCrossover Cable RJ-45 ConnectorCrossover Cable Crossover Cable INAModule System Programming Summary Merlin Magix AdministrationINA Module Administration Options DSU Channel Selection INA Module Administration OptionsActivate or Deactivate the Onboard CSU Selection Description INA Module Maintenance OptionsError Events INA Module Maintenance OptionsDescription INA ModuleMaintenance OptionsMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events Hour Event TotalsCurrent Events Clearing Error EventsMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ Current Menu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ ClearLine Loopback Test Menu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ LineLpbkMenu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ Demand TestsSurrogate Operation Backup and RestoreINA Module System Interactions Other System Interactions Pcmcia Flash Memory Card-Based Upgrade OperationBoard Renumbering Print ReportsSystem Restart ReplacementCondition Explanation System Erase Frigid StartINA Module System Interactions Index-1 IndexIndex-2 IndexIndex-3 Index-4 T1/PRIIndex-5