Lucent Technologies Network Access Module manual Installation and Configuration Steps

Page 20

Installation and Configuration Steps

Ethernet Port. This RJ-45 connector provides a 10BaseT Ethernet connection. See “Connect an Ethernet Cable” on page 3-4.

Ethernet Link LED. This green LED indicates link integrity to a 10BaseT hub. See “Ethernet LEDs” on page 3-6.

Reboot Button. This button resets the router hardware and reboots ComOS. It has no effect on MERLIN MAGIX voice operation. You will need a thin object such as a straightened paper click to activate this recessed switch.

T1/PRI Connection. This RJ-45 connector connects the T1/PRI line. See “Connect a T1/PRI Cable” on page 3-3.

DS-1 Test Jacks. There are three pairs of jacks for DS-1 troubleshooting. See “Using the DS-1 Test Jacks” on page A-5.

Installation and Configuration Steps

1.Collect information about your T1 or PRI line.

See “T1/PRI Provisioning” on page 2-1for a preview of the values you need.

2.Collect information about the network and routing configuration. See “Network Settings” on page 2-2for a preview of the values you need.

3.Install the INA module in the MERLIN MAGIX system. See “Install the INA Module in a Carrier” on page 3-1.

4.Configure the T1 or PRI line using the MERLIN MAGIX console. See “Set Up T1/PRI on the MERLIN MAGIX” on page 2-1.

5.Assign data channels to the router using the MERLIN MAGIX console. See “Assign T1/PRI Channels” on page 2-2.

6.Connect the INA module front panel cables. See “Connect Cables” on page 3-1.

7.Configure the INA module. See one of the following:

–“Using the INAWizard” on page 4-1.

–“Using the Command Line Interface” on page 5-1.

–“Using PMVision” on page 6-1.

1-4	INA Module Installation and Configuration Guide

Image 20

Contents Merlin Magix Your Responsibility for Your System’s Security Year 2000 ComplianceCopyright and Trademarks Page Contents Using the Command Line Interface ContentsUsing the INAWizard Using PMVision TroubleshootingCable Specifications Merlin Magix AdministrationIndex ViiiSafety Instructions Important Safety Instructions -SAVE These InstructionsImportant Safety Instructions -SAVE These Instructions About This Guide AudienceRelated Documentation Merlin Magix DocumentationCalling Group Supervisor and Service Observer User Guide SPM, Maintenance and TroubleshootingRelated Documentation Merlin Legend Superscript Communications System, ReleasePortMaster Documentation Additional ReferencesDocument Conventions Document AdvisoriesDocument Conventions Convention Use Examples Bold fontLimited Warranty Technical SupportINA Module Training Courses USA Dealers and Value-Added Resellers VARS. CallSubscribing to PortMaster Mailing Lists Xvi INA Administration INA ModuleINA Module Description On the Merlin MagixINA Front Panel On the INA ModuleINA Front Panel 1INA Module Front Panel INA ModuleCollect information about your T1 or PRI line Installation and Configuration StepsInstallation and Configuration Steps Getting Ready for Configuration Set Up T1/PRI on the Merlin MagixSetting Example T1/PRI ProvisioningAssign T1/PRI Channels Network SettingsNetwork Settings Settings Example 16172.26.131.37 192.198.32.17Hours 192.198.32.33Installing the INA Module Install the INA Module in a CarrierConnect Cables Connect a Serial Passthrough CableSet DIP Switches Set DIP switch 1 to the rightSet DIP switch 2 to the left Connect CablesConnect a T1/PRI Cable Installing the INA ModuleConnect a Console Optional Connect an Ethernet Cable Observe LED BehaviorT1/PRI LEDs Observe LED BehaviorSystem LED System LEDEthernet LEDs 8Ethernet LEDsUsing the INAWizard Install the WizardConnect the Workstation to the INA Module Over a LANRun the Wizard Connect a Console Using the Command Line InterfaceUsing the C0 Console Port Using a Telnet Session Using the Passthrough Serial ConnectionSet the Administrative Password LogCommand set password Password Command set ether0 broadcast highlowSet the Ether0 Network Address Set the IP Address and NetmaskSet the Default Route Gateway Command set sysname StringSet the System Name Set the System NameConfigure the WAN Port Set the Name ServiceSet the Name Server Set the Domain NameSet the Port IP Address Optional Set Up Additional WAN PortsSet the Channel Rate Set the Destination IP Address Set the NetmaskSet the Transport Protocol Apply Filters to the WAN Port OptionalConfigure the WAN Port Using PMVision Install PMVisionRun PMVision Using a Crossover CableRun PMVision Communicate with the INA Module Using PMVisionCommunicate with the INA Module Using Configuration Functions Working with Configuration PanelsSelecting PMVision Functions Selecting PMVision FunctionsEnter Basic Settings Working with Configuration DisplaysSave EditEdit System name INA→ Configure→ Snmp Default gateway INA→ Configure→ GlobalName service type INA→ Configure→ Global Name server address INA→ Configure→ GlobalUsing the Backup and Restore Functions Back Up the INA Module SettingsRestore the INA Module Settings 6PMVision Backup DialogObserving LED Behavior Troubleshooting aLED Behavior Possible Cause Solution Attach a console Observing Boot MessagesObserving Boot Messages Press the reboot button Observe the boot messages displayed on the console screenError at failed Field Possible Message ExplanationMemory address AddressUsing the DS-1 Test Jacks Table A-2Interpreting Diagnostic Boot MessagesUsing the DS-1 Test Jacks Test Jack Label Description and UsageFigure A-1DS-1 Test Jack Locations Using the DS-1 Test Jacks Cable Specifications SignalCables Specified Console CableEthernet Connector Transmission Type Cable Type Distance T1/PRI CableEthernet Interface T1/PRI CableCrossover Cable RJ-45 ConnectorCrossover Cable Crossover Cable INAModule System Programming Summary Merlin Magix AdministrationINA Module Administration Options DSU Channel Selection INA Module Administration OptionsActivate or Deactivate the Onboard CSU INA Module Maintenance Options Error EventsINA Module Maintenance Options Selection DescriptionINA ModuleMaintenance Options Menu Maintenance→ Slot→ Slot#→ Enter→ Error EventsHour Event Totals DescriptionClearing Error Events Menu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ CurrentMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ Clear Current EventsMenu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ LineLpbk Menu Maintenance→ Slot→ Slot#→ Enter→ Demand test→Demand Tests Line Loopback TestSurrogate Operation Backup and RestoreINA Module System Interactions Pcmcia Flash Memory Card-Based Upgrade Operation Board RenumberingPrint Reports Other System InteractionsReplacement Condition Explanation System EraseFrigid Start System RestartINA Module System Interactions Index Index-1Index Index-2Index-3 T1/PRI Index-4Index-5