Lucent Technologies Network Access Module manual Restore the INA Module Settings

Page 48

Selecting PMVision Functions

Figure 6-6PMVision Backup Dialog

Restore the INA Module Settings

To restore the INA module settings captured in a backup file, select

INA→ Maintain→ Restore. Enter or browse to the backup filename on the Restore panel (Figure 6-7)and click Restore. The restored values overwrite any values existing in the INA module. A backup file created with a selective backup overwrites only the selected configuration values and leaves the others unchanged.

Figure 6-7PMVision Restore Dialog

6-8	INA Module Installation and Configuration Guide

Image 48

Contents Merlin Magix Your Responsibility for Your System’s Security Year 2000 ComplianceCopyright and Trademarks Page Contents Contents Using the INAWizardUsing the Command Line Interface Using PMVision TroubleshootingCable Specifications Merlin Magix AdministrationIndex ViiiSafety Instructions Important Safety Instructions -SAVE These InstructionsImportant Safety Instructions -SAVE These Instructions About This Guide AudienceRelated Documentation Merlin Magix DocumentationCalling Group Supervisor and Service Observer User Guide SPM, Maintenance and TroubleshootingRelated Documentation Merlin Legend Superscript Communications System, ReleasePortMaster Documentation Additional ReferencesDocument Conventions Document AdvisoriesDocument Conventions Convention Use Examples Bold fontLimited Warranty Technical SupportINA Module Training Courses USA Dealers and Value-Added Resellers VARS. CallSubscribing to PortMaster Mailing Lists Xvi INA Administration INA ModuleINA Module Description On the Merlin MagixOn the INA Module INA Front PanelINA Front Panel 1INA Module Front Panel INA ModuleInstallation and Configuration Steps Installation and Configuration StepsCollect information about your T1 or PRI line Getting Ready for Configuration Set Up T1/PRI on the Merlin MagixSetting Example T1/PRI ProvisioningNetwork Settings Network SettingsAssign T1/PRI Channels Settings Example 16172.26.131.37 192.198.32.17Hours 192.198.32.33Installing the INA Module Install the INA Module in a CarrierConnect Cables Connect a Serial Passthrough CableSet DIP Switches Set DIP switch 1 to the rightSet DIP switch 2 to the left Connect CablesInstalling the INA Module Connect a Console OptionalConnect a T1/PRI Cable Connect an Ethernet Cable Observe LED BehaviorT1/PRI LEDs Observe LED BehaviorSystem LED System LEDEthernet LEDs 8Ethernet LEDsUsing the INAWizard Install the WizardConnect the Workstation to the INA Module Over a LANRun the Wizard Using the Command Line Interface Using the C0 Console PortConnect a Console Using a Telnet Session Using the Passthrough Serial ConnectionSet the Administrative Password LogCommand set password Password Command set ether0 broadcast highlowSet the Ether0 Network Address Set the IP Address and NetmaskSet the Default Route Gateway Command set sysname StringSet the System Name Set the System NameConfigure the WAN Port Set the Name ServiceSet the Name Server Set the Domain NameSet Up Additional WAN Ports Set the Channel RateSet the Port IP Address Optional Set the Destination IP Address Set the NetmaskSet the Transport Protocol Apply Filters to the WAN Port OptionalConfigure the WAN Port Using PMVision Install PMVisionUsing a Crossover Cable Run PMVisionRun PMVision Using PMVision Communicate with the INA ModuleCommunicate with the INA Module Using Configuration Functions Working with Configuration PanelsSelecting PMVision Functions Selecting PMVision FunctionsEnter Basic Settings Working with Configuration DisplaysSave EditEdit System name INA→ Configure→ Snmp Default gateway INA→ Configure→ GlobalName service type INA→ Configure→ Global Name server address INA→ Configure→ GlobalUsing the Backup and Restore Functions Back Up the INA Module SettingsRestore the INA Module Settings 6PMVision Backup DialogTroubleshooting a LED Behavior Possible Cause SolutionObserving LED Behavior Observing Boot Messages Observing Boot MessagesAttach a console Press the reboot button Observe the boot messages displayed on the console screenError at failed Field Possible Message ExplanationMemory address AddressUsing the DS-1 Test Jacks Table A-2Interpreting Diagnostic Boot MessagesUsing the DS-1 Test Jacks Test Jack Label Description and UsageFigure A-1DS-1 Test Jack Locations Using the DS-1 Test Jacks Cable Specifications SignalCables Specified Console CableEthernet Connector Transmission Type Cable Type Distance T1/PRI CableEthernet Interface T1/PRI CableRJ-45 Connector Crossover CableCrossover Cable Crossover Cable Merlin Magix Administration INA Module Administration OptionsINAModule System Programming Summary INA Module Administration Options Activate or Deactivate the Onboard CSUDSU Channel Selection INA Module Maintenance Options Error EventsINA Module Maintenance Options Selection DescriptionINA ModuleMaintenance Options Menu Maintenance→ Slot→ Slot#→ Enter→ Error EventsHour Event Totals DescriptionClearing Error Events Menu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ CurrentMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ Clear Current EventsMenu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ LineLpbk Menu Maintenance→ Slot→ Slot#→ Enter→ Demand test→Demand Tests Line Loopback TestBackup and Restore INA Module System InteractionsSurrogate Operation Pcmcia Flash Memory Card-Based Upgrade Operation Board RenumberingPrint Reports Other System InteractionsReplacement Condition Explanation System EraseFrigid Start System RestartINA Module System Interactions Index Index-1Index Index-2Index-3 T1/PRI Index-4Index-5