Lucent Technologies Network Access Module manual Connect an Ethernet Cable, Observe LED Behavior

Page 28

Observe LED Behavior

Figure 3-4T1/PRI Connection

D

S 1

M

O

N

M

O

N

T1/PRI port

1210-003

Connect an Ethernet Cable

Use a category 5 twisted pair cable, as specified by the EIA/TIA-568-B wiring standard, with an RJ-48C connector to connect the INA Ethernet connector (Figure 3-5) to the nearest network hub. See “Ethernet Interface” on page B-2for more information.

Figure 3-5Ether0 Connection

E

T

H

E

R

N E T

Ethernet port (Ether 0)

1210-004

Observe LED Behavior

Check the T1/PRI, system, and Ethernet LEDs to verify that the installed INA module is operating properly.

T1/PRI LEDs

These LEDs (Figure 3-6) indicate the status of the T1/PRI line and operate in the same way as on a 100D module. Make sure they indicate that the T1/PRI line is operating properly.

3-4

INA Module Installation and Configuration Guide

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Merlin Magix Your Responsibility for Your System’s Security Year 2000 ComplianceCopyright and Trademarks Page Contents Using the INAWizard ContentsUsing the Command Line Interface Using PMVision TroubleshootingCable Specifications Merlin Magix AdministrationIndex ViiiSafety Instructions Important Safety Instructions -SAVE These InstructionsImportant Safety Instructions -SAVE These Instructions About This Guide AudienceRelated Documentation Merlin Magix DocumentationCalling Group Supervisor and Service Observer User Guide SPM, Maintenance and TroubleshootingRelated Documentation Merlin Legend Superscript Communications System, ReleasePortMaster Documentation Additional ReferencesDocument Conventions Document AdvisoriesDocument Conventions Convention Use Examples Bold fontLimited Warranty Technical SupportINA Module Training Courses USA Dealers and Value-Added Resellers VARS. CallSubscribing to PortMaster Mailing Lists Xvi INA Administration INA ModuleINA Module Description On the Merlin MagixINA Front Panel On the INA ModuleINA Front Panel 1INA Module Front Panel INA ModuleInstallation and Configuration Steps Installation and Configuration StepsCollect information about your T1 or PRI line Getting Ready for Configuration Set Up T1/PRI on the Merlin MagixSetting Example T1/PRI ProvisioningNetwork Settings Network SettingsAssign T1/PRI Channels Settings Example 16172.26.131.37 192.198.32.17Hours 192.198.32.33Installing the INA Module Install the INA Module in a CarrierConnect Cables Connect a Serial Passthrough CableSet DIP Switches Set DIP switch 1 to the rightSet DIP switch 2 to the left Connect CablesConnect a Console Optional Installing the INA ModuleConnect a T1/PRI Cable Connect an Ethernet Cable Observe LED BehaviorT1/PRI LEDs Observe LED BehaviorSystem LED System LEDEthernet LEDs 8Ethernet LEDsUsing the INAWizard Install the WizardConnect the Workstation to the INA Module Over a LANRun the Wizard Using the C0 Console Port Using the Command Line InterfaceConnect a Console Using a Telnet Session Using the Passthrough Serial ConnectionSet the Administrative Password LogCommand set password Password Command set ether0 broadcast highlowSet the Ether0 Network Address Set the IP Address and NetmaskSet the Default Route Gateway Command set sysname StringSet the System Name Set the System NameConfigure the WAN Port Set the Name ServiceSet the Name Server Set the Domain NameSet the Channel Rate Set Up Additional WAN PortsSet the Port IP Address Optional Set the Destination IP Address Set the NetmaskSet the Transport Protocol Apply Filters to the WAN Port OptionalConfigure the WAN Port Using PMVision Install PMVisionRun PMVision Using a Crossover CableRun PMVision Communicate with the INA Module Using PMVisionCommunicate with the INA Module Using Configuration Functions Working with Configuration PanelsSelecting PMVision Functions Selecting PMVision FunctionsEnter Basic Settings Working with Configuration DisplaysSave EditEdit System name INA→ Configure→ Snmp Default gateway INA→ Configure→ GlobalName service type INA→ Configure→ Global Name server address INA→ Configure→ GlobalUsing the Backup and Restore Functions Back Up the INA Module SettingsRestore the INA Module Settings 6PMVision Backup DialogLED Behavior Possible Cause Solution Troubleshooting aObserving LED Behavior Observing Boot Messages Observing Boot MessagesAttach a console Press the reboot button Observe the boot messages displayed on the console screenError at failed Field Possible Message ExplanationMemory address AddressUsing the DS-1 Test Jacks Table A-2Interpreting Diagnostic Boot MessagesUsing the DS-1 Test Jacks Test Jack Label Description and UsageFigure A-1DS-1 Test Jack Locations Using the DS-1 Test Jacks Cable Specifications SignalCables Specified Console CableEthernet Connector Transmission Type Cable Type Distance T1/PRI CableEthernet Interface T1/PRI CableCrossover Cable RJ-45 ConnectorCrossover Cable Crossover Cable INA Module Administration Options Merlin Magix AdministrationINAModule System Programming Summary Activate or Deactivate the Onboard CSU INA Module Administration OptionsDSU Channel Selection INA Module Maintenance Options Error EventsINA Module Maintenance Options Selection DescriptionINA ModuleMaintenance Options Menu Maintenance→ Slot→ Slot#→ Enter→ Error EventsHour Event Totals DescriptionClearing Error Events Menu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ CurrentMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ Clear Current EventsMenu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ LineLpbk Menu Maintenance→ Slot→ Slot#→ Enter→ Demand test→Demand Tests Line Loopback TestINA Module System Interactions Backup and RestoreSurrogate Operation Pcmcia Flash Memory Card-Based Upgrade Operation Board RenumberingPrint Reports Other System InteractionsReplacement Condition Explanation System EraseFrigid Start System RestartINA Module System Interactions Index Index-1Index Index-2Index-3 T1/PRI Index-4Index-5
Top Page Image Contents