Lucent Technologies Network Access Module Board Renumbering, Print Reports, ConditionExplanation

Page 68

INA Module System Interactions

Board Renumbering

The INA module works in the same manner as the 100D module for board renumbering. Use board renumbering to replace a 100D module with a 100R module, and vice versa. After the board renumbering, T1/PRI data that had been previously administered for the replaced module is associated with the new module. The data channels assigned to the 100R are now be unassigned on the 100D module.

￿Print Reports

The System Inventory Report is enhanced to include summary information about INA modules present in the system. This summary information is presented under the 100-RUlabel.

PCMCIA Flash Memory Card-Based Upgrade Operation

The INA module firmware is upgradeable using the MERLIN MAGIX PCMCIA card.

Note – Performing an upgrade to the INA module firmware using the MERLIN MAGIX PCMCIA card does not upgrade the INA module router software. Router software is upgraded separately with the PMVision application. Depending upon the nature of the upgrade, either a INA module firmware upgrade, or a router software upgrade, or both might be required.

Other System Interactions

Table C-5shows system conditions applying to the INA module.

Table C-5INA Module System Interactions

ConditionExplanation

Idle Conditions - The system might be forced into an idle state

System Forced while the module is routing data traffic. When

Idlethe system is in the forced idle condition, the router on the INA module continues to operate and route data traffic.

Slot Busy-OutAn INA module can be busied out even if the module is routing data traffic. Busying out the module disrupts both voice and router services. Voice and data services are restored when the module is restored.

C-8

INA Module Installation and Configuration Guide

Image 68
Contents Merlin Magix Your Responsibility for Your System’s Security Year 2000 ComplianceCopyright and Trademarks Page Contents Using the Command Line Interface ContentsUsing the INAWizard Using PMVision TroubleshootingCable Specifications Merlin Magix AdministrationIndex ViiiSafety Instructions Important Safety Instructions -SAVE These InstructionsImportant Safety Instructions -SAVE These Instructions About This Guide AudienceRelated Documentation Merlin Magix DocumentationCalling Group Supervisor and Service Observer User Guide SPM, Maintenance and TroubleshootingRelated Documentation Merlin Legend Superscript Communications System, ReleasePortMaster Documentation Additional ReferencesDocument Conventions Document AdvisoriesDocument Conventions Convention Use Examples Bold fontLimited Warranty Technical SupportINA Module Training Courses USA Dealers and Value-Added Resellers VARS. CallSubscribing to PortMaster Mailing Lists Xvi INA Administration INA ModuleINA Module Description On the Merlin MagixINA Front Panel On the INA ModuleINA Front Panel 1INA Module Front Panel INA ModuleCollect information about your T1 or PRI line Installation and Configuration StepsInstallation and Configuration Steps Getting Ready for Configuration Set Up T1/PRI on the Merlin MagixSetting Example T1/PRI ProvisioningAssign T1/PRI Channels Network SettingsNetwork Settings Settings Example 16172.26.131.37 192.198.32.17Hours 192.198.32.33Installing the INA Module Install the INA Module in a CarrierConnect Cables Connect a Serial Passthrough CableSet DIP Switches Set DIP switch 1 to the rightSet DIP switch 2 to the left Connect CablesConnect a T1/PRI Cable Installing the INA ModuleConnect a Console Optional Connect an Ethernet Cable Observe LED BehaviorT1/PRI LEDs Observe LED BehaviorSystem LED System LEDEthernet LEDs 8Ethernet LEDsUsing the INAWizard Install the WizardConnect the Workstation to the INA Module Over a LANRun the Wizard Connect a Console Using the Command Line InterfaceUsing the C0 Console Port Using a Telnet Session Using the Passthrough Serial ConnectionSet the Administrative Password LogCommand set password Password Command set ether0 broadcast highlowSet the Ether0 Network Address Set the IP Address and NetmaskSet the Default Route Gateway Command set sysname StringSet the System Name Set the System NameConfigure the WAN Port Set the Name ServiceSet the Name Server Set the Domain NameSet the Port IP Address Optional Set Up Additional WAN PortsSet the Channel Rate Set the Destination IP Address Set the NetmaskSet the Transport Protocol Apply Filters to the WAN Port OptionalConfigure the WAN Port Using PMVision Install PMVisionRun PMVision Using a Crossover CableRun PMVision Communicate with the INA Module Using PMVisionCommunicate with the INA Module Using Configuration Functions Working with Configuration PanelsSelecting PMVision Functions Selecting PMVision FunctionsEnter Basic Settings Working with Configuration DisplaysSave EditEdit System name INA→ Configure→ Snmp Default gateway INA→ Configure→ GlobalName service type INA→ Configure→ Global Name server address INA→ Configure→ GlobalUsing the Backup and Restore Functions Back Up the INA Module SettingsRestore the INA Module Settings 6PMVision Backup DialogObserving LED Behavior Troubleshooting aLED Behavior Possible Cause Solution Attach a console Observing Boot MessagesObserving Boot Messages Press the reboot button Observe the boot messages displayed on the console screenError at failed Field Possible Message ExplanationMemory address AddressUsing the DS-1 Test Jacks Table A-2Interpreting Diagnostic Boot MessagesUsing the DS-1 Test Jacks Test Jack Label Description and UsageFigure A-1DS-1 Test Jack Locations Using the DS-1 Test Jacks Cable Specifications SignalCables Specified Console CableEthernet Connector Transmission Type Cable Type Distance T1/PRI CableEthernet Interface T1/PRI CableCrossover Cable RJ-45 ConnectorCrossover Cable Crossover Cable INAModule System Programming Summary Merlin Magix AdministrationINA Module Administration Options DSU Channel Selection INA Module Administration OptionsActivate or Deactivate the Onboard CSU INA Module Maintenance Options Error EventsINA Module Maintenance Options Selection DescriptionINA ModuleMaintenance Options Menu Maintenance→ Slot→ Slot#→ Enter→ Error EventsHour Event Totals DescriptionClearing Error Events Menu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ CurrentMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ Clear Current EventsMenu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ LineLpbk Menu Maintenance→ Slot→ Slot#→ Enter→ Demand test→Demand Tests Line Loopback TestSurrogate Operation Backup and RestoreINA Module System Interactions Pcmcia Flash Memory Card-Based Upgrade Operation Board RenumberingPrint Reports Other System InteractionsReplacement Condition Explanation System EraseFrigid Start System RestartINA Module System Interactions Index Index-1Index Index-2Index-3 T1/PRI Index-4Index-5