Lucent Technologies Network Access Module manual Current Events, Selected Interval Events

Page 65

INA Module Maintenance Options

Each error statistic represents the sum of error events from all valid intervals including the current interval. The message “9999” represents an overflow situation.

You can refresh the 24-hour total screen by pressing Back and then pressing 24 hr total again.

Current Events

The Current error event screen reports error statistics for the 15-minute interval that is currently active. The elapsed minutes line displays the number of minutes that have elapsed for the current interval. The elapsed minutes display ranges from 0 to 15 and is rounded to the nearest minute. From your system programming console, use the following sequence to access the Current screen. Be sure to select the corresponding INA module slot number.

Menu: MaintenanceSlotSlot#EnterError EventsCurrent

The events reported are the same as for the 24 hour event totals screen.

You can refresh the Current screen by pressing Back and then pressing Current again.

￿Selected Interval Events

The Selected Interval Events screen reports on error statistics for a specific 15-minute interval from the past 24 hours. Ninety-six 15-minute intervals occur in a 24-hour period. Interval 1 is the most recent 15 minute interval just before the current interval, and interval 96 is the oldest interval. From your system programming console, use the following sequence to select a specific interval from the Selected Interval Events screen. Be sure to select the corresponding INA module slot number.

Menu: MaintenanceSlotSlot#EnterErrorEventsInterval

Interval#Enter

Note – Invalid intervals have all zeroes for error data, but no visual indication is given to show that the interval is not valid. You can, however, compute the total number of invalid intervals by subtracting the valid interval count on the 24-hour total screen from 96.

Clearing Error Events

The Clear Error Events screen causes error events for all intervals, including the current interval, to be cleared. From your system programming console, use the following sequence to access the Clear Error Events screen. Be sure to select the corresponding INA module slot number.

Menu: MaintenanceSlotSlot#EnterError EventsClear

To stop the clear event and retain all error events, press Back or Cancel. You will return to the Error events screen.

C-5

Image 65
Contents Merlin Magix Year 2000 Compliance Your Responsibility for Your System’s SecurityCopyright and Trademarks Page Contents Using the Command Line Interface ContentsUsing the INAWizard Troubleshooting Using PMVisionCable Specifications Merlin Magix AdministrationViii IndexImportant Safety Instructions -SAVE These Instructions Safety InstructionsImportant Safety Instructions -SAVE These Instructions Audience About This GuideRelated Documentation Merlin Magix DocumentationSPM, Maintenance and Troubleshooting Calling Group Supervisor and Service Observer User GuideRelated Documentation Merlin Legend Superscript Communications System, ReleaseAdditional References PortMaster DocumentationDocument Advisories Document ConventionsDocument Conventions Convention Use Examples Bold fontTechnical Support Limited WarrantyINA Module Training Courses USA Dealers and Value-Added Resellers VARS. CallSubscribing to PortMaster Mailing Lists Xvi INA Module INA AdministrationINA Module Description On the Merlin MagixINA Front Panel On the INA ModuleINA Front Panel INA Module 1INA Module Front PanelCollect information about your T1 or PRI line Installation and Configuration StepsInstallation and Configuration Steps Set Up T1/PRI on the Merlin Magix Getting Ready for ConfigurationSetting Example T1/PRI ProvisioningAssign T1/PRI Channels Network SettingsNetwork Settings Settings Example 192.198.32.17 16172.26.131.37Hours 192.198.32.33Install the INA Module in a Carrier Installing the INA ModuleConnect Cables Connect a Serial Passthrough CableSet DIP switch 1 to the right Set DIP SwitchesSet DIP switch 2 to the left Connect CablesConnect a T1/PRI Cable Installing the INA ModuleConnect a Console Optional Observe LED Behavior Connect an Ethernet CableT1/PRI LEDs Observe LED BehaviorSystem LED System LED8Ethernet LEDs Ethernet LEDsInstall the Wizard Using the INAWizardConnect the Workstation to the INA Module Over a LANRun the Wizard Connect a Console Using the Command Line InterfaceUsing the C0 Console Port Using the Passthrough Serial Connection Using a Telnet SessionSet the Administrative Password LogCommand set ether0 broadcast highlow Command set password PasswordSet the Ether0 Network Address Set the IP Address and NetmaskCommand set sysname String Set the Default Route GatewaySet the System Name Set the System NameSet the Name Service Configure the WAN PortSet the Name Server Set the Domain NameSet the Port IP Address Optional Set Up Additional WAN PortsSet the Channel Rate Set the Netmask Set the Destination IP AddressSet the Transport Protocol Apply Filters to the WAN Port OptionalConfigure the WAN Port Install PMVision Using PMVisionRun PMVision Using a Crossover CableRun PMVision Communicate with the INA Module Using PMVisionCommunicate with the INA Module Working with Configuration Panels Using Configuration FunctionsSelecting PMVision Functions Selecting PMVision FunctionsWorking with Configuration Displays Enter Basic SettingsSave EditDefault gateway INA→ Configure→ Global Edit System name INA→ Configure→ SnmpName service type INA→ Configure→ Global Name server address INA→ Configure→ GlobalBack Up the INA Module Settings Using the Backup and Restore Functions6PMVision Backup Dialog Restore the INA Module SettingsObserving LED Behavior Troubleshooting aLED Behavior Possible Cause Solution Attach a console Observing Boot MessagesObserving Boot Messages Observe the boot messages displayed on the console screen Press the reboot buttonField Possible Message Explanation Error at failedMemory address AddressTable A-2Interpreting Diagnostic Boot Messages Using the DS-1 Test JacksTest Jack Label Description and Usage Using the DS-1 Test JacksFigure A-1DS-1 Test Jack Locations Using the DS-1 Test Jacks Signal Cable SpecificationsCables Specified Console CableT1/PRI Cable Ethernet Connector Transmission Type Cable Type DistanceEthernet Interface T1/PRI CableCrossover Cable RJ-45 ConnectorCrossover Cable Crossover Cable INAModule System Programming Summary Merlin Magix AdministrationINA Module Administration Options DSU Channel Selection INA Module Administration OptionsActivate or Deactivate the Onboard CSU Error Events INA Module Maintenance OptionsINA Module Maintenance Options Selection DescriptionMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events INA ModuleMaintenance OptionsHour Event Totals DescriptionMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ Current Clearing Error EventsMenu Maintenance→ Slot→ Slot#→ Enter→ Error Events→ Clear Current EventsMenu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ Menu Maintenance→ Slot→ Slot#→ Enter→ Demand test→ LineLpbkDemand Tests Line Loopback TestSurrogate Operation Backup and RestoreINA Module System Interactions Board Renumbering Pcmcia Flash Memory Card-Based Upgrade OperationPrint Reports Other System InteractionsCondition Explanation System Erase ReplacementFrigid Start System RestartINA Module System Interactions Index-1 IndexIndex-2 IndexIndex-3 Index-4 T1/PRIIndex-5