Cypress CY7C67300 manual Booster Interface, Crystal Interface, Booster Pins, Crystal Pins

Page 11

CY7C67300

Booster Interface

EZ-Host has an on chip power booster circuit for use with power supplies that range between 2.7V and 3.6V. The booster circuit boosts the power to 3.3V nominal to supply power for the entire chip. The booster circuit requires an external inductor, diode, and capacitor. During power down mode, the circuit is disabled to save power. Figure 6 shows how to connect the booster circuit.

Figure 6. Power Supply Connection With Booster

Booster Pins

Table 17. Charge Pump Interface Pins

Pin Name

Pin Number

BOOSTVcc

16

 

 

VSWITCH

14

 

 

Crystal Interface

BOOSTVcc

VSWITCH

L1

D1

2.7V to 3.6V Power Supply

The recommended crystal circuit to be used with EZ-Host is shown in Figure 8 If an oscillator is used instead of a crystal circuit, connect it to XTALIN and leave XTALOUT unconnected. For further information about the crystal requirements, see Table 132, Crystal Requirements on page 83.

Noted that the CLKSEL pin (pin 38) is sampled after reset to determine what crystal or clock source frequency is used. For normal operation, 12 MHz is required so the CLKSEL pin must have a 47K ohm pull up resistor to VCC..

Figure 8. Crystal Interface

VCC AVCC

C1

XTALIN

CY7C67300

Y1

12MHz

Component details:

■ L1: Inductor with inductance of 10 µH and a current rating of at

least 250 mA

■ D1: Schottky diode with a current rating of at least 250 mA

XTALOUT

Parallel Resonant Fundamental Mode 500uW

20-33pf ±5%

■ C1: Tantalum or ceramic capacitor with a capacitance of at least

2.2 µF

Figure 7 shows how to connect the power supply when the booster circuit is not being used.

Figure 7. Power Supply Connection Without Booster

BOOSTVcc

3.0V to 3.6V

Power Supply

C1 = 22 pF

 

 

 

 

 

 

C2 = 22 pF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Crystal Pins

Table 18. Crystal Pins

Pin Name

Pin Number

XTALIN

29

 

 

XTALOUT

28

 

 

VSWITCH

VCC

AVCC

Document #: 38-08015 Rev. *J

Page 11 of 99

[+] Feedback

Page 10 Page 12
Image 11
Page 10 Page 12
Contents
Typical Applications EZ-Host FeaturesCY7C67300 Block Diagram Interface Descriptions IntroductionFunctional Overview USB Interface Interface Options for External Memory Bus Pins MEM PinsOTG Interface USB Interface Pins Pin Name Pin NumberOTG Interface Pins Pin Name Pin Number External Memory Interface Up to 256k x 16 External Code/Data Page Mode External Memory Interface PinsExternal Memory Interface Pins Pin Name Pin Number External Memory Interface Block DiagramsSerial Peripheral Interface General Purpose IO Interface GpioUart Interface I2C Eeprom Interface Programmable Pulse/PWM Interface High-Speed Serial InterfaceIDE Interface HPI Interface Pins 3 Pin Name Pin NumberHPI Interface Pins 3 Host Port InterfaceActual IDE Throughput ModeIDE Interface Pins Pin Name Pin Number Charge Pump Interface Pins Pin Name Pin NumberBooster Interface Booster PinsCrystal Pins Crystal Pins Pin Name Pin NumberOperational Modes Boot Configuration InterfaceBoot Configuration Interface Boot ModeSleep Power Savings and Reset DescriptionPower Saving Mode Description Memory Map Document # 38-08015 Rev. *JPage 15 Bank Selected 0xC018 0xC01AProcessor Control Registers RegistersRevision Register Bank RegisterBank Register Example Hex Value Binary Value ReservedCPU Speed Definition Processor Speed Host/Device 1B Wake Enable Bit Power Control RegisterHost/Device 2B Wake Enable Bit Host/Device 2A Wake Enable BitSPI Interrupt Enable Bit Sleep Enable BitInterrupt Enable Register Halt Enable Bit OTG Interrupt Enable BitUart Interrupt Enable Bit HSS Interrupt Enable BitMailbox Interrupt Enable Bit Out Mailbox Interrupt Enable BitPort 1B Diagnostic Enable Bit USB Diagnostic RegisterPort 2B Diagnostic Enable Bit Port 2A Diagnostic Enable BitExternal Memory Registers Extended Page n Map Register Upper Address Enable Register 0xC038 R/WUpper Address Enable Bit Extended Page n Map Register R/WTimer Registers WDT Enable Bit Watchdog Timer RegisterTimeout Flag Bit Lock Enable BitPort B D+ Status Bit Timer n RegisterGeneral USB Registers USB n Control RegisterEnable Mode Select BitPort B Resistors Enable Bit Port a Resistors Enable BitUSB Host Only Register Register Name Address Host 1/Host Port a SOF/EOP Enable Bit ReservedPreamble Enable Bit USB Host Only RegistersSequence Select Bit Sync Enable BitHost n Address Register ISO Enable Bit Arm Enable BitNAK Flag Bit Port Select BitUnderflow Flag Bit Stall Flag BitHost n PID Register Error Flag BitSequence Status Bit Host n PID Register WHost n Count Result Register Endpoint Select Bits PID Select DefinitionPID Select Host n Count Result Register RHost n Device Address Register Host n Interrupt Enable RegisterVbus Interrupt Enable Bit ID Interrupt Enable BitPort B Connect Change Interrupt Enable Bit SOF/EOP Interrupt Enable BitPort B Wake Interrupt Enable Bit Port a Wake Interrupt Enable BitPort B Connect Change Interrupt Flag Bit SOF/EOP Interrupt Flag BitPort B Wake Interrupt Flag Bit Port a Wake Interrupt Flag BitHost 1 Frame Register 0xC096 Host 2 Frame Register 0xC0B6 Host n SOF/EOP Counter Register RHost n SOF/EOP Counter Register Host n Frame Register RDevice n Endpoint n Control Register IN/OUT Ignore Enable BitUSB Device Only Registers Device n Endpoint n Control Register R/WDirection Select Bit Stall Enable BitNAK Interrupt Enable Bit Enable BitDevice n Endpoint n Count Register Device n Endpoint n Count Register R/WException Flag Bit Device n Endpoint n Status Register R/WDevice n Endpoint n Status Register OUT Exception Flag BitDevice n Endpoint n Count Result Register Setup Flag BitSequence Flag Bit Device n Endpoint n Count Result Register R/WDevice n Port Select Register Device n Interrupt Enable Register R/WDevice n Interrupt Enable Register Port Select Bit Device n Port Select Register R/WEP6 Interrupt Enable Bit SOF/EOP Timeout Interrupt Enable BitReset Interrupt Enable Bit EP7 Interrupt Enable BitDevice n Status Register R/W EP0 Interrupt Enable BitDevice n Address Register W Device n Address RegisterEP5 Interrupt Flag Bit Reset Interrupt Flag BitEP7 Interrupt Flag Bit EP6 Interrupt Flag BitEP1 Interrupt Flag Bit SOF/EOP Timeout Flag BitSOF/EOP Timeout Interrupt Counter Bits EP2 Interrupt Flag BitOTG Control Register Reserved Vbus Pull-up Enable BitOTG Control Registers Device n SOF/EOP Count RegisterGpio Registers HSS Enable Bit Write Protect Enable BitSAS Enable Bit Mode Select Definition Gpio Configuration 108Gpio n Input Data Register Interrupt 0 Enable BitInterrupt 0 Polarity Select Bit Reserved Gpio n Output Data RegisterIDE Registers IDE Start Address Register Mode Select DefinitionIDE Start Address Register 0xC04A R/W IDE Control Register IDE Interrupt Enable BitIDE Enable Bit IDE Stop Address RegisterHSS Registers Register Name Address HSS RegistersIDE PIO Port Registers 0xC050 0xC06F R/W HSS Control Register Xoff Enable BitCTS Enable Bit Receive Interrupt Enable BitHSS Baud Rate Register Packet Mode Select BitTransmit Ready Bit Receive Overflow Flag BitHSS Data Register 0xC076 R/W HSS Transmit Gap Register 0xC074 R/WHSS Transmit Gap Register Transmit Gap Select BitsHSS Receive Counter Register HSS Receive Counter Register 0xC07A R/WHSS Transmit Counter Register HSS Transmit Address Register 0xC07C R/WHSS Transmit Address Register HSS Transmit Counter Register 0xC07E R/WInterrupt Routing Register Vbus to HPI Enable BitHPI Registers HPI Breakpoint Register HPI Registers Register Name AddressSOF/EOP1 to HPI Enable Bit ID to HPI Enable BitSOF/EOP2 to HPI Enable Bit SOF/EOP2 to CPU Enable BitHPI Mailbox Register 0xC0C6 R/W SIEXmsg Register WSIE1msg Register SIE2msg Register SIEXmsg RegisterID Flag Bit Reset2 Flag BitHPI Status Port Vbus Flag BitMailbox Out Flag Bit Reset1 Flag BitSPI Registers Done1 Flag BitMaster Enable Bit 3Wire Enable BitPhase Select Bit Master Active Enable BitSCK Strobe Bit Byte Mode BitRead Enable Bit SPI Control RegisterFifo Error Flag Bit SPI Interrupt Enable RegisterTransmit Interrupt Enable Bit Transfer Interrupt Enable BitTransfer Interrupt Flag Bit Receive Interrupt Flag BitTransmit Interrupt Flag Bit SPI Interrupt Clear RegisterSPI CRC Value Register Receive CRC Bit CRC Mode Definition CRCMode CRC Polynomial 1514CRC Enable Bit CRC Clear BitSPI Transmit Address Register SPI Data Register 0xC0D6 R/WSPI Data Register SPI Transmit Address Register 0xC0D8 R/WSPI Receive Count Register SPI Transmit Count RegisterSPI Receive Address Register Uart Registers Uart Data Register 0xC0E4 R/W Uart Status Register 0xC0E2 RUart Status Register Receive buffer full Receive buffer emptyPWM Control Register PWM Enable BitPWM Registers PWM Registers Register Name AddressPWM 0 Enable Bit PWM 3 Enable BitPWM 2 Enable Bit PWM 1 Enable BitPWM n Stop Register PWM n Start Register R/WPWM n Start Register PWM n Stop Register R/WPWM Cycle Count Register PWM Cycle Count Register 0xC0FA R/WPin Descriptions Name Type Pin DiagramPin Descriptions D8/MISO D11/MOSIMosi SPI Mosi SCK SPI SCKGPIO26/CTS/PWM3 GPIO29/OTGIDGPIO28/TX GPIO27/RXTie to Gnd for normal operation Booster Power input 2.7V toCrystal Requirements XTALIN, Xtalout DC CharacteristicsAbsolute Maximum Ratings Operating ConditionsGND USB TransceiverClock Timing AC Timing CharacteristicsReset Timing LOW Sram Read Cycle15Sram Read Cycle Parameters Description Min Typical Max Unit High Sram Write CycleSram Write Cycle Parameters Parameter Description Min Typical Max UnitSDA OUT I2C Eeprom Timing-Serial IOSCL HPI Host Port Interface Write Cycle Timing Read Cycle Time Chip Select Hold Data Access Time, from HPInRD fallingHPI Host Port Interface Read Cycle Timing Read Pulse WidthIDE Timing HSS Byte Mode TransmitHSS Block Mode Transmit HSS Byte and Block Mode ReceiveRegister Summary Register SummaryHardware CTS/RTS Handshake HSS SOF/EOP CRC SOF/EOP2 Pb-Free Package DiagramsOrdering Information Ordering Information Ordering Code Package TypeOrig. Submis Description of Change Sion Date Document HistoryUSB Sales, Solutions, and Legal InformationWorldwide Sales and Design Support Products PSoC Solutions
Top Page Image Contents