Edimax Technology AR-7211B V2 manual You can choose Interface or IP Address, NAT Forwarding

Page 71

 

Field

 

 

Description

 

 

 

 

 

 

Protocol

 

 

Choose the transport layer protocol that the

 

 

 

service type uses. You can choose TCP or UDP.

 

 

 

 

 

 

 

 

 

 

WAN Setting

 

 

You can choose Interface or IP Address.

 

 

 

 

 

 

WAN Interface

 

 

Choose the WAN interface that will apply to the

 

 

 

virtual server.

 

 

 

 

 

 

 

 

 

 

WAN Port

 

 

Choose the access port on the WAN.

 

 

 

 

 

 

LAN Open Port

 

 

Enter the port number of the specified service

 

 

 

type.

 

 

 

 

 

 

 

 

 

 

 

 

 

Enter the IP address of the virtual server. It is in

 

LAN IP Address

 

 

the same network segment with LAN IP address

 

 

 

 

of the router.

 

 

 

 

 

5.6.2.3. NAT Forwarding

Click NAT Forwarding in the left pane, and the page shown in the following figure will appear. Under 1483MER or 1483Routed mode, if NAPT (Network Address Port Translation) is enabled, the Local IP Address is configured as 192.168.1.3 and the Remote IP Address is configured as 202.32.0.2 - the PC with the LAN IP192.168.1.3 will use 202.32.0.2 when it is connected to the Internet via the router without NAPT control.

71

Page 70 Page 72
Image 71
Page 70 Page 72
Contents AR-7211A V2 / AR-7211B Copyright Contents Routing NAT IP QoS Snmp Others System Requirements Package ContentsSafety Precautions Adsl LED & Button DefinitionsLAN  DMZ Features Napt  DNSConnect the router to your LAN network ConfigurationConnect the Adsl line No telephone before the splitter Check the Adsl LED status Firewall settingsPC LAN IP configuration Page Select Internet Protocol TCP/IP and then click Properties Page Windows Vista and Windows XP WindowsWindows Vista Windows XP Page Setup Wizard EZmax Setup WizardPlease select your product Page Page Page Page Internet Connection Type Parameter VPI VCI Bridge Mode Dynamic IP Address Static IP Firmware Upgrade Accessing the Router Web ConfigurationVCI Internet ConnectionField Description VPIPPPoE/PPPoA On Demand, or Manual 2 MER/1483 Routed Bridged Dhcp Server Field Description LAN Interface SetupLAN IP 192.168.2.1Device Info StatusWAN LANAdsl Statistic StatisticsLAN IP NetworkARP Duplex,10Mbps/FullDuplex,10Mbps/Half Downlist100Mbps/FullDuplex,100Mbps/HalfCurrent Allowed MAC Address Table Current Allowed MAC Address Table can accessField Description Duplex,Auto Negotiation MACField Description Field Description If set to Dhcp Relay, the router acts a surrogate Dhcp WAN Dhcp Static IPMER, PPPoE, PPPoA, 1483 Routed or IPoA On Demand or Manual PPP SettingsWAN IP Settings PVC into the Current ATM VC Table If you choose Connect on Demand ATM VCCVPI/VCI Auto PVC Bridged PPPoE or Disable BridgeMacclone PCR ATM SettingsCBR, nrt-VBR or rt-VBR MBS Adsl SettingsCdvt SCRDNS ServiceDynDNS.org or TZO DdnsMAC Filter Firewall2.1. IP/Port Filter URL Filter Software Forbidden Anti-DoSUpnp TR-069 Igmp ProxyConnection Request URLACS ACL DebugTo the Current ACL Table You can choose Interface or IP Address Static Route AdvancedRouting RIP NAT RIPVirtual Server  If User-defined Service Name is selected, youNAT Forwarding ALG NATPort Trigger NAT Exclude IP2.8 NAT IP Mapping FTP ALG PortIP QoS You can choose strict prior or WFQ You can choose stream based, 802.1p based or Dscp BasedSnmp You can choose Normal Service, Minimize CostMinimize Delay Maximize Reliability, Maximize Throughput, orField Description Others Client LimitUpdate AdminCommit/Reboot  Restore to the factory default configurationBackup/Restore Upgrade FirmwareLog PasswordTime NTP ConfigurationTraceroute DiagnosticPing PingOAM Loopback DscpDiag-Test Adsl Statistics255.255.255.0, respectively Trouble ShootingDeclaration of Conformity
Top Page Image Contents