Edimax Technology AR-7211B V2 manual Debug, Acl

Page 64

Field	Description
Password	The connection password provided by TR-069
	service.
Debug
Show Message	Select Enable to display ACS SOAP messages on the
	serial console.
CPE sends GetRPC	When enabled, the router contacts the ACS to obtain
	configuration updates.
Skip MReboot	Specify whether to send an MReboot event code in
	the inform message.
Delay	Specify whether to start the TR-069 program after a
	short delay.
Auto-Execution	Specify whether to automatically start the TR-069
	after the router is powered on.

5.5.6.ACL

Choose Service > ACL and you will arrive at the following screen. Here, you can permit the data packets from LAN or WAN to access the router. You can configure the IP address for Access Control List (ACL). If ACL is enabled, only the effective IP address in the ACL can access the router.

Note: If you select Enable in ACL capability, ensure that your host IP address is in ACL list before it takes effect.

64

Image 64

Contents AR-7211A V2 / AR-7211B Copyright Contents Routing NAT IP QoS Snmp Others Safety Precautions Package ContentsSystem Requirements LED & Button Definitions AdslLAN Features  Napt DNS  DMZConnect the Adsl line ConfigurationConnect the router to your LAN network No telephone before the splitter PC LAN IP configuration Firewall settingsCheck the Adsl LED status Page Select Internet Protocol TCP/IP and then click Properties Page Windows Windows Vista and Windows XPWindows Vista Windows XP Page EZmax Setup Wizard Setup WizardPlease select your product Page Page Page Page Internet Connection Type Parameter VPI VCI Bridge Mode Dynamic IP Address Static IP Firmware Upgrade Web Configuration Accessing the RouterInternet Connection Field DescriptionVPI VCIPPPoE/PPPoA On Demand, or Manual 2 MER/1483 Routed Bridged Field Description LAN Interface Setup LAN IP192.168.2.1 Dhcp ServerStatus Device InfoLAN WANStatistics Adsl StatisticARP NetworkLAN IP Downlist100Mbps/FullDuplex,100Mbps/Half Duplex,10Mbps/FullDuplex,10Mbps/HalfCurrent Allowed MAC Address Table can access Field Description Duplex,Auto NegotiationMAC Current Allowed MAC Address TableField Description Field Description If set to Dhcp Relay, the router acts a surrogate Dhcp Dhcp Static IP WANMER, PPPoE, PPPoA, 1483 Routed or IPoA WAN IP Settings PPP SettingsOn Demand or Manual PVC into the Current ATM VC Table VPI/VCI ATM VCCIf you choose Connect on Demand Macclone Bridged PPPoE or Disable BridgeAuto PVC CBR, nrt-VBR or rt-VBR ATM SettingsPCR Adsl Settings CdvtSCR MBSService DNSDdns DynDNS.org or TZO2.1. IP/Port Filter FirewallMAC Filter URL Filter Anti-DoS Software ForbiddenUpnp Igmp Proxy TR-069ACS URLConnection Request Debug ACLTo the Current ACL Table You can choose Interface or IP Address Routing AdvancedStatic Route RIP RIP NAT If User-defined Service Name is selected, you Virtual ServerNAT Forwarding NAT ALGNAT Exclude IP Port TriggerFTP ALG Port 2.8 NAT IP MappingIP QoS You can choose stream based, 802.1p based or Dscp Based You can choose strict prior or WFQYou can choose Normal Service, Minimize Cost Minimize DelayMaximize Reliability, Maximize Throughput, or SnmpField Description Client Limit OthersAdmin Commit/Reboot Restore to the factory default configuration UpdateUpgrade Firmware Backup/RestorePassword LogNTP Configuration TimeDiagnostic PingPing TracerouteDscp OAM LoopbackAdsl Statistics Diag-TestTrouble Shooting 255.255.255.0, respectivelyDeclaration of Conformity