Edimax Technology AR-7211B V2 manual Field Description

Page 78

Community name (read-

The network administrators must use this password to

only)

read the information of this router.

Community name (read-

The network administrators must use this password to

write)

configure the information of the router.

5.6.5.Others

Select Advanced > Others. The submenu contains Bridge Setting, Client Limit and Others.

5.6.5.1. Bridge Setting

Click Bridge Setting in the left pane and you will arrive at the following page. This page is used to configure the bridge parameters. You can change the settings or view some information on the bridge and its attached ports.

 

Field

Description

Aging Time

If the host is idle for 300 seconds (default value), its entry

 

 

is deleted from the bridge table.

802.1d

Spanning

You can select Disabled or Enabled.

Tree

 

Select Enabled to provide path redundancy while

 

 

preventing undesirable loops in your network.

Show MACs

Click to show a list of the learned MAC addresses for the

 

 

bridge.

Click Show MACs and the following page will appear. This table shows a list of learned MAC addresses for this bridge.

78

Image 78
Contents AR-7211A V2 / AR-7211B Copyright Contents Routing NAT IP QoS Snmp Others Package Contents Safety PrecautionsSystem Requirements LED & Button Definitions AdslLAN  DNS Features Napt  DMZConfiguration Connect the Adsl lineConnect the router to your LAN network No telephone before the splitter Firewall settings PC LAN IP configurationCheck the Adsl LED status Page Select Internet Protocol TCP/IP and then click Properties Page Windows Windows Vista and Windows XPWindows Vista Windows XP Page EZmax Setup Wizard Setup WizardPlease select your product Page Page Page Page Internet Connection Type Parameter VPI VCI Bridge Mode Dynamic IP Address Static IP Firmware Upgrade Web Configuration Accessing the RouterVPI Internet ConnectionField Description VCIPPPoE/PPPoA On Demand, or Manual 2 MER/1483 Routed Bridged 192.168.2.1 Field Description LAN Interface SetupLAN IP Dhcp ServerStatus Device InfoLAN WANStatistics Adsl StatisticNetwork ARPLAN IP Downlist100Mbps/FullDuplex,100Mbps/Half Duplex,10Mbps/FullDuplex,10Mbps/HalfMAC Current Allowed MAC Address Table can accessField Description Duplex,Auto Negotiation Current Allowed MAC Address TableField Description Field Description If set to Dhcp Relay, the router acts a surrogate Dhcp Dhcp Static IP WANMER, PPPoE, PPPoA, 1483 Routed or IPoA PPP Settings WAN IP SettingsOn Demand or Manual PVC into the Current ATM VC Table ATM VCC VPI/VCIIf you choose Connect on Demand Bridged PPPoE or Disable Bridge MaccloneAuto PVC ATM Settings CBR, nrt-VBR or rt-VBRPCR SCR Adsl SettingsCdvt MBSService DNSDdns DynDNS.org or TZOFirewall 2.1. IP/Port FilterMAC Filter URL Filter Anti-DoS Software ForbiddenUpnp Igmp Proxy TR-069URL ACSConnection Request Debug ACLTo the Current ACL Table You can choose Interface or IP Address Advanced RoutingStatic Route RIP RIP NAT If User-defined Service Name is selected, you Virtual ServerNAT Forwarding NAT ALGNAT Exclude IP Port TriggerFTP ALG Port 2.8 NAT IP MappingIP QoS You can choose stream based, 802.1p based or Dscp Based You can choose strict prior or WFQMaximize Reliability, Maximize Throughput, or You can choose Normal Service, Minimize CostMinimize Delay SnmpField Description Client Limit Others Restore to the factory default configuration AdminCommit/Reboot UpdateUpgrade Firmware Backup/RestorePassword LogNTP Configuration TimePing DiagnosticPing TracerouteDscp OAM LoopbackAdsl Statistics Diag-TestTrouble Shooting 255.255.255.0, respectivelyDeclaration of Conformity