Edimax Technology AR-7211B V2 manual Diagnostic, Ping, Traceroute

Page 84

	Field			Description

				enable NTP if you want to configure the parameters
				of NTP.

	Server			Set the primary NTP server manually.

	Server2			Set the secondary NTP server manually.

	Time Zone			Choose the time zone in which area you are from
	Time Zone			the drop down list.
				the drop down list.

5.8.Diagnostic

In the navigation bar, click Diagnostic. The Diagnostic page that is displayed contains Ping, Traceroute, OAM Loopback, ADSL Statistics and Diag-Test.

5.8.1.Ping

Choose Diagnostic > Ping. The page shown in the following figure will appear.

Field	Description
Host	Enter the valid IP address or domain name.
PING	Click it to start to Ping.

5.8.2.Traceroute

Choose Diagnostic > Traceroute. Using this route diagnosis you can see the route your PC data takes to another PC on the Internet.

84

Image 84

Contents AR-7211A V2 / AR-7211B Copyright Contents Routing NAT IP QoS Snmp Others Package Contents Safety PrecautionsSystem Requirements LED & Button Definitions AdslLAN Features  Napt DNS  DMZConfiguration Connect the Adsl lineConnect the router to your LAN network No telephone before the splitter Firewall settings PC LAN IP configurationCheck the Adsl LED status Page Select Internet Protocol TCP/IP and then click Properties Page Windows Windows Vista and Windows XPWindows Vista Windows XP Page EZmax Setup Wizard Setup WizardPlease select your product Page Page Page Page Internet Connection Type Parameter VPI VCI Bridge Mode Dynamic IP Address Static IP Firmware Upgrade Web Configuration Accessing the RouterInternet Connection Field DescriptionVPI VCIPPPoE/PPPoA On Demand, or Manual 2 MER/1483 Routed Bridged Field Description LAN Interface Setup LAN IP192.168.2.1 Dhcp ServerStatus Device InfoLAN WANStatistics Adsl StatisticNetwork ARPLAN IP Downlist100Mbps/FullDuplex,100Mbps/Half Duplex,10Mbps/FullDuplex,10Mbps/HalfCurrent Allowed MAC Address Table can access Field Description Duplex,Auto NegotiationMAC Current Allowed MAC Address TableField Description Field Description If set to Dhcp Relay, the router acts a surrogate Dhcp Dhcp Static IP WANMER, PPPoE, PPPoA, 1483 Routed or IPoA PPP Settings WAN IP SettingsOn Demand or Manual PVC into the Current ATM VC Table ATM VCC VPI/VCIIf you choose Connect on Demand Bridged PPPoE or Disable Bridge MaccloneAuto PVC ATM Settings CBR, nrt-VBR or rt-VBRPCR Adsl Settings CdvtSCR MBSService DNSDdns DynDNS.org or TZOFirewall 2.1. IP/Port FilterMAC Filter URL Filter Anti-DoS Software ForbiddenUpnp Igmp Proxy TR-069URL ACSConnection Request Debug ACLTo the Current ACL Table You can choose Interface or IP Address Advanced RoutingStatic Route RIP RIP NAT If User-defined Service Name is selected, you Virtual ServerNAT Forwarding NAT ALGNAT Exclude IP Port TriggerFTP ALG Port 2.8 NAT IP MappingIP QoS You can choose stream based, 802.1p based or Dscp Based You can choose strict prior or WFQYou can choose Normal Service, Minimize Cost Minimize DelayMaximize Reliability, Maximize Throughput, or SnmpField Description Client Limit OthersAdmin Commit/Reboot Restore to the factory default configuration UpdateUpgrade Firmware Backup/RestorePassword LogNTP Configuration TimeDiagnostic PingPing TracerouteDscp OAM LoopbackAdsl Statistics Diag-TestTrouble Shooting 255.255.255.0, respectivelyDeclaration of Conformity