Eicon Networks DIVA T/A ISDN Modem manual AT% Commands

Page 20

 

 

Alphabetical List of Supported AT Commands

 

AT% Commands

 

 

 

 

 

 

AT%A2=n

Protocol Control (static)

40

 

 

 

 

 

AT%A4=n

ISDN Communication Speed

40

 

 

 

 

 

AT%A95=c

Incoming Data Call Answer

40

 

 

 

 

 

AT%M1=n

Local Endpoint Discriminator Class

46

 

 

 

 

 

AT%M2=n

Remote Endpoint Discriminator Class

46

 

 

 

 

 

AT%M3=n

Local Endpoint Discriminator Address

46

 

 

 

 

 

AT%M4=n

Remote Endpoint Discriminator Address

46

 

 

 

 

 

AT%P5=n

Enable Bandwidth Allocation Control Protocol / Bandwidth on Demand

46

 

 

 

 

 

AT%P6=n

Set Initial Billing Interval Timer

46

 

 

 

 

 

AT%P7=n

Set Billing Interval Timer

46

 

 

 

 

 

AT%P8=n

Dynamic Bandwidth Allocation

47

 

 

 

 

 

AT%P9=n

Second B-channel Connection Retries

47

 

 

 

 

 

AT%P10=n

Enable/disable PPP Echo-Requests

47

 

 

 

 

DIVA T/A ISDN Modem Reference Guide ◆ Page 20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Diva T/A Isdn Modem Reference Guide Eight Edition July 206-193-08 Contents What is ISDN? Diva T/A Isdn Modem Reference GuideWhat is ISDN? Isdn Communication Channels ChannelChannel Connecting to Isdn BRI and PRI Basic Rate AccessWhat is Multilink PPP? What is BACP/BOD? What is DBA? What is Always On / Dynamic Isdn AO/DI? What is Data Compression? Locating AT Commands Locating AT Commands AT Command Groups Alphabetical List of Supported AT Commands AT! Commands Alphabetical List of Supported AT CommandsAlphabetical List of Supported AT Commands AT% Commands AT& Commands AT* Commands AT Commands AT@ Commands Other AT Commands Registers AT$ Utility Commands Mini-monitor Commands General AT Commands General AT Commands Values for n Isdn Configuration CommandsDefaults Isdn Configuration Commands None default Default1INS-Net64, NI-1, or 5ESS, µ law will be used default AT!D3=nDefault null string this is an optional value AT!N2=nNumber. Numbers are separated by a semicolon AT!N3=nOn region 255 do not attempt 56k data call retry For more details, refer to the Rvscom documentationAT!X56=n COM Port Configuration Commands COM Port Configuration Commands RingFor example, Connect Upon connection, the Diva T/A reports the DCE speedCall Control Commands Call Control Commands ATAATH Configuration Commands Configuration Commands Use the default settings AT!V0=nProfile Commands Multilink PPP Commands Multilink PPP Commands Internet Protocol IP Endpoint Discriminator Class/AddressAT%M3=b3c665ac11 Always On / Dynamic Isdn AT Commands Always On / Dynamic Isdn AT Commands AT!X13=n when Bacp is disabled, see Will be opened after the delay specified by AT!X10Default 1000 bytes AT!X14=nDefault values for each setting, and is defined as follows Default AT!X22=nAT!X18 Defined as followsDefault CF PPP over AT!X25=nConnection numbers affects the range ofAT!X21. SeeAT!X21 AT!X26=nUtility Commands Utility Commands Internal TA access command reserved for VUStart or display the Result of a Lapd trace Start or Display the Result of a PPP traceStart an AO/DI X.25 Trace Enter the monitor on the next resetSoft reset the unit and enter the monitor Register Commands AT?Register Commands Analog Device Commands Analog Device Commands AT*FnTo be disabled Disable. Recommended for modem/fax callsEnable with default values default Enable using same terminal endpoint identifier as data portMini-monitor Commands AT Command Result Codes Carrier Connect AT Command Result CodesConnect Protocol Transparent Mode Connect 75T/1200RConnect 1200T/75R Protocol NoneIndex BACP/BOD
Top Page Image Contents