Eicon Networks DIVA T/A ISDN Modem manual Connect 75T/1200R, Connect 1200T/75R, Protocol None

Page 65

AT Command Result Codes

Code	Word Message
54	CARRIER 19200	CONNECT 19200

55	CARRIER 21600	CONNECT 21600

56	CARRIER 24000	CONNECT 24000

57	CARRIER 56000	CONNECT 56000

58	CARRIER 28800	CONNECT 28800

59	CARRIER 64000	CONNECT 64000

60	CARRIER 128000	CONNECT 128000

61	CARRIER 26400	CONNECT 26400

62	CARRIER 31200	CONNECT 31200

63	CARRIER 33600	CONNECT 33600

64	CARRIER 75T/1200R		CONNECT 75T/1200R

65	CARRIER 1200T/75R		CONNECT 1200T/75R

66	CARRIER 112000	CONNECT 112000

67	CARRIER 38400	CONNECT 38400

70	PROTOCOL: NONE

73	PROTOCOL: V42

79	PROTOCOL: MNP REL

80	PROTOCOL: MNP ALT

83	PROTOCOL: V120

84	PROTOCOL: V110

85	PROTOCOL: PPPC

86	PROTOCOL: MLPPP

89	PROTOCOL: TRV

90	PROTOCOL: TRANSPARENT MODE

DIVA T/A ISDN Modem Reference Guide ◆ Page 65

Image 65

Contents Diva T/A Isdn Modem Reference Guide Eight Edition July 206-193-08 Contents Diva T/A Isdn Modem Reference Guide What is ISDN?What is ISDN? Channel Isdn Communication ChannelsChannel Basic Rate Access Connecting to Isdn BRI and PRIWhat is Multilink PPP? What is BACP/BOD? What is DBA? What is Always On / Dynamic Isdn AO/DI? What is Data Compression? Locating AT Commands Locating AT Commands AT Command Groups Alphabetical List of Supported AT Commands Alphabetical List of Supported AT Commands AT! CommandsAlphabetical List of Supported AT Commands AT% Commands AT& Commands AT* Commands AT Commands AT@ Commands Other AT Commands Registers AT$ Utility Commands Mini-monitor Commands General AT Commands General AT Commands Values for n Isdn Configuration CommandsDefaults Isdn Configuration Commands Default1 None defaultINS-Net64, NI-1, or 5ESS, µ law will be used default AT!D3=nAT!N2=n Default null string this is an optional valueNumber. Numbers are separated by a semicolon AT!N3=nOn region 255 do not attempt 56k data call retry For more details, refer to the Rvscom documentationAT!X56=n COM Port Configuration Commands Ring COM Port Configuration CommandsUpon connection, the Diva T/A reports the DCE speed For example, ConnectCall Control Commands ATA Call Control CommandsATH Configuration Commands Configuration Commands AT!V0=n Use the default settingsProfile Commands Multilink PPP Commands Multilink PPP Commands Internet Protocol IP Endpoint Discriminator Class/AddressAT%M3=b3c665ac11 Always On / Dynamic Isdn AT Commands Always On / Dynamic Isdn AT Commands Will be opened after the delay specified by AT!X10 AT!X13=n when Bacp is disabled, seeDefault 1000 bytes AT!X14=nDefault AT!X22=n Default values for each setting, and is defined as followsAT!X18 Defined as followsAT!X25=n Default CF PPP overConnection numbers affects the range ofAT!X21. SeeAT!X21 AT!X26=nUtility Commands Internal TA access command reserved for VU Utility CommandsStart or display the Result of a Lapd trace Start or Display the Result of a PPP traceStart an AO/DI X.25 Trace Enter the monitor on the next resetSoft reset the unit and enter the monitor AT? Register CommandsRegister Commands Analog Device Commands AT*Fn Analog Device CommandsDisable. Recommended for modem/fax calls To be disabledEnable with default values default Enable using same terminal endpoint identifier as data portMini-monitor Commands AT Command Result Codes Carrier Connect AT Command Result CodesConnect Connect 75T/1200R Protocol Transparent ModeConnect 1200T/75R Protocol NoneBACP/BOD Index