Eicon Networks DIVA T/A ISDN Modem manual Profile Commands

Page 45

Profile Commands

The following table describes the profile commands:

AT&F	Use Factory Settings in Current Profile. Restores and loads all settings in the current
	profile with the original factory settings. Previously configured ISDN commands, stored
	telephone numbers, and the rate adaption control values are retained; all other settings
	are replaced.

AT&V	View Current and Stored Profiles. Displays the current and stored profiles as well as
	stored telephone numbers in your DIVA T/A.

AT&Wn	Save Settings as Profile n. Writes storable parameters of current profile in memory as
	stored profile n. Use when you are satisfied with your current configuration settings
	and want to save them to a specific stored profile n.

AT&Yn	Set Powerup Profile. Designates stored profile n as the powerup profile. Use to load
	your desired stored profile the next time your DIVA T/A is powered up.

AT>F	Use Factory Settings in All Profiles. Restores all stored profiles and the current profile
	to the original factory settings. Reverts the powerup profile to number 0. Use when you
	need to reset the device to its original factory settings.
	Warning: All previous user-defined settings are lost.

AT>FC	Reset Current Profile andTelephone Numbers . Resets the current profile and
	telephone numbers to the default factory settings.

AT>VC	View Current Profile. Presents a screen display of the current profile settings on your
	DIVA T/A.

AT>VCC	View Call and COM Port Parameters. Displays the Call and COM Port dynamic
	parameters.

AT>VCD	View Dynamic Parameters. Displays all dynamic parameters (Call, COM, V.120, V.110.
	PPP, MLPPP).

AT>VCP	View Protocol Parameters. Displays the protocol parameters (V.120, V.110, PPP,
	MLPPP).

AT>VCS	View Static Parameters. Displays all static parameters (ISDN, Rate Adaptation).

AT>VPn	View Stored Profile. Presents a screen display of the desired stored profile, where n is
	the number of the stored profile (0,1,2) you want to view.

AT>Z	Restart DIVA T/A Using Powerup Profile. Restarts your DIVA T/A using the powerup
	profile. Use anytime you want to load the powerup profile.

ATZn	Restart DIVA T/A Using Profile n. Restarts your DIVA T/A using stored profile n. Use
	after changing a static parameter.

DIVA T/A ISDN Modem Reference Guide ◆ Page 45

Image 45

Contents Diva T/A Isdn Modem Reference Guide Eight Edition July 206-193-08 Contents Diva T/A Isdn Modem Reference Guide What is ISDN?What is ISDN? Channel Isdn Communication ChannelsChannel Basic Rate Access Connecting to Isdn BRI and PRIWhat is Multilink PPP? What is BACP/BOD? What is DBA? What is Always On / Dynamic Isdn AO/DI? What is Data Compression? Locating AT Commands Locating AT Commands AT Command Groups Alphabetical List of Supported AT Commands Alphabetical List of Supported AT Commands AT! CommandsAlphabetical List of Supported AT Commands AT% Commands AT& Commands AT* Commands AT Commands AT@ Commands Other AT Commands Registers AT$ Utility Commands Mini-monitor Commands General AT Commands General AT Commands Isdn Configuration Commands DefaultsValues for n Isdn Configuration Commands Default1 None defaultINS-Net64, NI-1, or 5ESS, µ law will be used default AT!D3=nAT!N2=n Default null string this is an optional valueNumber. Numbers are separated by a semicolon AT!N3=nFor more details, refer to the Rvscom documentation AT!X56=nOn region 255 do not attempt 56k data call retry COM Port Configuration Commands Ring COM Port Configuration CommandsUpon connection, the Diva T/A reports the DCE speed For example, ConnectCall Control Commands ATA Call Control CommandsATH Configuration Commands Configuration Commands AT!V0=n Use the default settingsProfile Commands Multilink PPP Commands Multilink PPP Commands Endpoint Discriminator Class/Address AT%M3=b3c665ac11Internet Protocol IP Always On / Dynamic Isdn AT Commands Always On / Dynamic Isdn AT Commands Will be opened after the delay specified by AT!X10 AT!X13=n when Bacp is disabled, seeDefault 1000 bytes AT!X14=nDefault AT!X22=n Default values for each setting, and is defined as followsAT!X18 Defined as followsAT!X25=n Default CF PPP overConnection numbers affects the range ofAT!X21. SeeAT!X21 AT!X26=nUtility Commands Internal TA access command reserved for VU Utility CommandsStart or display the Result of a Lapd trace Start or Display the Result of a PPP traceEnter the monitor on the next reset Soft reset the unit and enter the monitorStart an AO/DI X.25 Trace AT? Register CommandsRegister Commands Analog Device Commands AT*Fn Analog Device CommandsDisable. Recommended for modem/fax calls To be disabledEnable with default values default Enable using same terminal endpoint identifier as data portMini-monitor Commands AT Command Result Codes AT Command Result Codes ConnectCarrier Connect Connect 75T/1200R Protocol Transparent ModeConnect 1200T/75R Protocol NoneBACP/BOD Index