Eicon Networks DIVA T/A ISDN Modem manual AT Commands

Page 23

		Alphabetical List of Supported AT Commands
	AT> Commands

	AT>?	Last AT Command Result Explained	29

	AT>F	Restores All Profiles to Factory Settings	45

	AT>FC	Reset Current Profile	45

	AT>Hs	View Help Information	29

	AT>VC	View Current Profile	45

	AT>VCC	View Call and COM Port Parameters	45

	AT>VCD	View Dynamic Parameters	45

	AT>VCP	View Protocol Parameters	45

	AT>VCS	View Static Parameters	45

	AT>VD	View Link And Connection Status Information	29

	AT>VDC	View Connection Status	29

	AT>VDD	Initialization Status Display (North America Only)	29

	AT>VDL	View Link States	29

	AT>VPn	View Stored Profile n	45

	AT>VT	View Stored Phone Numbers	29

	AT>VX	View X.25 Status (AO/DI)	29

	AT>Z	Restart the DIVA T/A	45

DIVA T/A ISDN Modem Reference Guide ◆ Page 23

Image 23

Contents Diva T/A Isdn Modem Reference Guide Eight Edition July 206-193-08 Contents Diva T/A Isdn Modem Reference Guide What is ISDN?What is ISDN? Channel Isdn Communication ChannelsChannel Basic Rate Access Connecting to Isdn BRI and PRIWhat is Multilink PPP? What is BACP/BOD? What is DBA? What is Always On / Dynamic Isdn AO/DI? What is Data Compression? Locating AT Commands Locating AT Commands AT Command Groups Alphabetical List of Supported AT Commands Alphabetical List of Supported AT Commands AT! CommandsAlphabetical List of Supported AT Commands AT% Commands AT& Commands AT* Commands AT Commands AT@ Commands Other AT Commands Registers AT$ Utility Commands Mini-monitor Commands General AT Commands General AT Commands Values for n Isdn Configuration CommandsDefaults Isdn Configuration Commands AT!D3=n None defaultDefault1 INS-Net64, NI-1, or 5ESS, µ law will be used defaultAT!N3=n Default null string this is an optional valueAT!N2=n Number. Numbers are separated by a semicolonOn region 255 do not attempt 56k data call retry For more details, refer to the Rvscom documentationAT!X56=n COM Port Configuration Commands Ring COM Port Configuration CommandsUpon connection, the Diva T/A reports the DCE speed For example, ConnectCall Control Commands ATA Call Control CommandsATH Configuration Commands Configuration Commands AT!V0=n Use the default settingsProfile Commands Multilink PPP Commands Multilink PPP Commands Internet Protocol IP Endpoint Discriminator Class/AddressAT%M3=b3c665ac11 Always On / Dynamic Isdn AT Commands Always On / Dynamic Isdn AT Commands AT!X14=n AT!X13=n when Bacp is disabled, seeWill be opened after the delay specified by AT!X10 Default 1000 bytesDefined as follows Default values for each setting, and is defined as followsDefault AT!X22=n AT!X18AT!X26=n Default CF PPP overAT!X25=n Connection numbers affects the range ofAT!X21. SeeAT!X21Utility Commands Start or Display the Result of a PPP trace Utility CommandsInternal TA access command reserved for VU Start or display the Result of a Lapd traceStart an AO/DI X.25 Trace Enter the monitor on the next resetSoft reset the unit and enter the monitor AT? Register CommandsRegister Commands Analog Device Commands AT*Fn Analog Device CommandsEnable using same terminal endpoint identifier as data port To be disabledDisable. Recommended for modem/fax calls Enable with default values defaultMini-monitor Commands AT Command Result Codes Carrier Connect AT Command Result CodesConnect Protocol None Protocol Transparent ModeConnect 75T/1200R Connect 1200T/75RBACP/BOD Index