Eicon Networks DIVA T/A ISDN Modem manual Endpoint Discriminator Class/Address, AT%M3=b3c665ac11

Page 48

Multilink PPP Commands

Endpoint Discriminator Class/Address

The following table describes the list of classes and permitted addresses for certain MultiLink PPP commands.

Class

Description

Address Format

0

Null Class

No address is used.

 

 

 

1

Locally Assigned

Uses a hexadecimal format with a maximum length of 40

 

Address

characters.

 

 

Valid characters: “0-9, a-f”. The number of digits must be even (ex.

 

 

AT%M3=b3c665ac11).

 

 

 

2

Internet Protocol (IP)

Uses a numerical format with a maximum length of 15 characters.

 

Address

Valid characters: “0-9” (ex. AT%M4=192.219.23.100).

 

 

 

 

 

3

IEEE 802.1 Globally

Uses a hexadecimal format with an exact length of 12 characters.

 

Assigned MAC Address

Valid characters: “0-9, a-f” (ex. AT%M3=b3c665ac1fff).

 

 

 

 

 

4

PPP Magic-Number

Uses a hexadecimal format with a maximum length of 40

 

Block

characters, and the length must be a multiple of 8.

 

 

Valid characters: “0-9, a-f” (ex. AT%M3=b3c665acffff0001).

 

 

 

5

Public Switched

Uses a normal telephone number with a maximum length of 15.

 

Network Directory

Valid characters are “0-9, *, #”.

 

Number

 

 

 

 

255

Accept Any Remote

No address is used. This class is valid only for remote endpoint

 

Endpoint Discriminator

discriminators (EPDs), and is used to accept any remote EPDs

 

 

received that are all part of the same bundle.

 

 

 

DIVA T/A ISDN Modem Reference Guide Page 48

Image 48
Contents Diva T/A Isdn Modem Reference Guide Eight Edition July 206-193-08 Contents What is ISDN? Diva T/A Isdn Modem Reference GuideWhat is ISDN? Isdn Communication Channels ChannelChannel Connecting to Isdn BRI and PRI Basic Rate AccessWhat is Multilink PPP? What is BACP/BOD? What is DBA? What is Always On / Dynamic Isdn AO/DI? What is Data Compression? Locating AT Commands Locating AT Commands AT Command Groups Alphabetical List of Supported AT Commands AT! Commands Alphabetical List of Supported AT CommandsAlphabetical List of Supported AT Commands AT% Commands AT& Commands AT* Commands AT Commands AT@ Commands Other AT Commands Registers AT$ Utility Commands Mini-monitor Commands General AT Commands General AT Commands Isdn Configuration Commands DefaultsValues for n Isdn Configuration Commands None default Default1INS-Net64, NI-1, or 5ESS, µ law will be used default AT!D3=nDefault null string this is an optional value AT!N2=nNumber. Numbers are separated by a semicolon AT!N3=nFor more details, refer to the Rvscom documentation AT!X56=nOn region 255 do not attempt 56k data call retry COM Port Configuration Commands COM Port Configuration Commands RingFor example, Connect Upon connection, the Diva T/A reports the DCE speedCall Control Commands Call Control Commands ATAATH Configuration Commands Configuration Commands Use the default settings AT!V0=nProfile Commands Multilink PPP Commands Multilink PPP Commands Endpoint Discriminator Class/Address AT%M3=b3c665ac11Internet Protocol IP Always On / Dynamic Isdn AT Commands Always On / Dynamic Isdn AT Commands AT!X13=n when Bacp is disabled, see Will be opened after the delay specified by AT!X10Default 1000 bytes AT!X14=nDefault values for each setting, and is defined as follows Default AT!X22=nAT!X18 Defined as followsDefault CF PPP over AT!X25=nConnection numbers affects the range ofAT!X21. SeeAT!X21 AT!X26=nUtility Commands Utility Commands Internal TA access command reserved for VUStart or display the Result of a Lapd trace Start or Display the Result of a PPP traceEnter the monitor on the next reset Soft reset the unit and enter the monitorStart an AO/DI X.25 Trace Register Commands AT?Register Commands Analog Device Commands Analog Device Commands AT*FnTo be disabled Disable. Recommended for modem/fax callsEnable with default values default Enable using same terminal endpoint identifier as data portMini-monitor Commands AT Command Result Codes AT Command Result Codes ConnectCarrier Connect Protocol Transparent Mode Connect 75T/1200RConnect 1200T/75R Protocol NoneIndex BACP/BOD