Eicon Networks DIVA T/A ISDN Modem manual AT!V0=n, Use the default settings

Page 44

V.110 Configuration Commands

Use the following AT commands to specify the V.110 configuration on your DIVA T/A (International version only).

AT!V0=n	V.110 Configuration Override. Specifies whether the DIVA T/A uses the COM port
	setting to configure V.110 or overrides them with user settings.
	n=0	Use the default settings.
	n=1	Override the COM port settings as per AT!V1, AT!V2, AT!V3, AT!V4, and AT!V5
		(default).

AT!V1=n	V.110 Stream Rate. Specifies the V.110 Stream Rate
	Values: 1200, 2400, 4800, 9600, 19200 (default).

AT!V2=n	V.110 Character Length. Specifies the character length.
	Values: 7, 8 (default).

AT!V3=n	V.110 Parity. Specifies the parity used for V.110.
	n=0	None (default).
	n=1	Even.
	n=2	Odd.
	n=3	One.
	n=4	Zero.

AT!V4=n	V.110 Stop Bits. Specifies the Stop Bits used for V.110.
	Values: 1 (default), 2.

AT!V5=n	V.110 Flow Control. Specifies the Flow Control method to be used for V.110.
	n=0	None.
	n=1	Receive only (default).
	n=2	Transmit only.
	n=3	Receive and transmit.

DIVA T/A ISDN Modem Reference Guide ◆ Page 44

Image 44

Contents Diva T/A Isdn Modem Reference Guide Eight Edition July 206-193-08 Contents What is ISDN? Diva T/A Isdn Modem Reference GuideWhat is ISDN? Isdn Communication Channels ChannelChannel Connecting to Isdn BRI and PRI Basic Rate AccessWhat is Multilink PPP? What is BACP/BOD? What is DBA? What is Always On / Dynamic Isdn AO/DI? What is Data Compression? Locating AT Commands Locating AT Commands AT Command Groups Alphabetical List of Supported AT Commands AT! Commands Alphabetical List of Supported AT CommandsAlphabetical List of Supported AT Commands AT% Commands AT& Commands AT* Commands AT Commands AT@ Commands Other AT Commands Registers AT$ Utility Commands Mini-monitor Commands General AT Commands General AT Commands Values for n Isdn Configuration CommandsDefaults Isdn Configuration Commands None default Default1INS-Net64, NI-1, or 5ESS, µ law will be used default AT!D3=nDefault null string this is an optional value AT!N2=nNumber. Numbers are separated by a semicolon AT!N3=nOn region 255 do not attempt 56k data call retry For more details, refer to the Rvscom documentationAT!X56=n COM Port Configuration Commands COM Port Configuration Commands RingFor example, Connect Upon connection, the Diva T/A reports the DCE speedCall Control Commands Call Control Commands ATAATH Configuration Commands Configuration Commands Use the default settings AT!V0=nProfile Commands Multilink PPP Commands Multilink PPP Commands Internet Protocol IP Endpoint Discriminator Class/AddressAT%M3=b3c665ac11 Always On / Dynamic Isdn AT Commands Always On / Dynamic Isdn AT Commands AT!X13=n when Bacp is disabled, see Will be opened after the delay specified by AT!X10Default 1000 bytes AT!X14=nDefault values for each setting, and is defined as follows Default AT!X22=nAT!X18 Defined as followsDefault CF PPP over AT!X25=nConnection numbers affects the range ofAT!X21. SeeAT!X21 AT!X26=nUtility Commands Utility Commands Internal TA access command reserved for VUStart or display the Result of a Lapd trace Start or Display the Result of a PPP traceStart an AO/DI X.25 Trace Enter the monitor on the next resetSoft reset the unit and enter the monitor Register Commands AT?Register Commands Analog Device Commands Analog Device Commands AT*FnTo be disabled Disable. Recommended for modem/fax callsEnable with default values default Enable using same terminal endpoint identifier as data portMini-monitor Commands AT Command Result Codes Carrier Connect AT Command Result CodesConnect Protocol Transparent Mode Connect 75T/1200RConnect 1200T/75R Protocol NoneIndex BACP/BOD