Eicon Networks DIVA T/A ISDN Modem manual Isdn Configuration Commands

Page 32

ISDN Configuration Commands

 

AT!C1=n

ISDN Switch Type. Specifies the ISDN Switch Type.

 

 

For North American Firmware:

 

 

n=0

National ISDN

 

 

n=1

AT&T 5ESS Custom

 

 

n=9

Auto-detect switch type (default for North America). The DIVA T/A automatically

 

 

 

determines the correct switch type to be used (National ISDN or AT&T 5ESS

 

 

 

Custom).

 

 

For International Firmware:

 

 

n=2

EuroISDN (default).

 

 

n=3

Australia - Microlink (TPH1962/TS013).

 

 

n=4

INS-Net64 (Japan).

 

 

n=5

China ISDN.

 

 

n=6

Singapore

 

 

n=11 Australia - OnRamp (Telstra's ETSI service)

 

 

Note: This parameter does not take effect until you restart your DIV AT/A.

 

 

 

 

AT!C4=n

Enable/Disable Non-Initializing mode (first B-channel) (North American only).

 

 

Specifies whether the first B-channel is set to Non-Initializing mode.

 

 

n=0

Disable Non-initializing mode (default).

 

 

n=1

Enable Non-initializing mode.

 

 

Note: This parameter does not take effect until you restart your DIV AT/A.

 

 

 

 

AT!C5=n

Enable/Disable Non-Initializing mode (second B-channel) (North American only).

 

 

Specifies whether the second B-channel is set to Non-Initializing mode.

 

 

n=0

Disable Non-initializing mode (default).

 

 

n=1

Enable Non-initializing mode

 

 

Note: This parameter does not take effect until you restart your DIV AT/A.

 

 

 

 

AT!C6=n

SPID Number for 1st B-channel(North American only). The SPID (Service Profile

 

 

Identifier) as assigned by your local telephone company. This number is a unique ID

 

 

which identifies an ISDN terminal to the local ISDN switch.

 

 

Default: null string.

 

 

Note: This parameter does not take effect until you restart your DIV AT/A.

 

 

 

 

AT!C7=n

SPID Number for 2nd B-channel(North America only). The SPID (Service Profile

 

 

Identifier) as assigned by your local telephone company. This number is a unique ID

 

 

which identifies an ISDN terminal to the local ISDN switch.

 

 

Default: null string.

 

 

Note: This parameter does not take effect until you restart your DIV AT/A.

 

 

 

 

AT!D1=n

Default DTE Speed. Specifies the speed of the DTE, when the DTE characteristics

 

 

cannot be determined by AutoBauding (AT has not been typed since power up).

 

 

Values: 1200, 2400, 3600, 4800, 7200, 9600, 12000, 14400, 19200, 24000, 28800,

 

 

38400, 57600, 64000, 115200 or 230400.

 

 

Default: 115200.

 

 

 

 

AT!D2=n

Default Databits Length. Specifies the length of the Databits, when the DTE

 

 

characteristics cannot be determined by AutoBauding (AT has not been typed since

 

 

power up).

 

 

Values: 7, 8.

 

 

Default: 8.

 

 

 

 

 

 

 

 

 

 

 

DIVA T/A ISDN Modem Reference Guide ◆ Page 32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Diva T/A Isdn Modem Reference Guide Eight Edition July 206-193-08 Contents What is ISDN? Diva T/A Isdn Modem Reference GuideWhat is ISDN? Isdn Communication Channels ChannelChannel Connecting to Isdn BRI and PRI Basic Rate AccessWhat is Multilink PPP? What is BACP/BOD? What is DBA? What is Always On / Dynamic Isdn AO/DI? What is Data Compression? Locating AT Commands Locating AT Commands AT Command Groups Alphabetical List of Supported AT Commands AT! Commands Alphabetical List of Supported AT CommandsAlphabetical List of Supported AT Commands AT% Commands AT& Commands AT* Commands AT Commands AT@ Commands Other AT Commands Registers AT$ Utility Commands Mini-monitor Commands General AT Commands General AT Commands Values for n Isdn Configuration CommandsDefaults Isdn Configuration Commands None default Default1INS-Net64, NI-1, or 5ESS, µ law will be used default AT!D3=nDefault null string this is an optional value AT!N2=nNumber. Numbers are separated by a semicolon AT!N3=nOn region 255 do not attempt 56k data call retry For more details, refer to the Rvscom documentationAT!X56=n COM Port Configuration Commands COM Port Configuration Commands RingFor example, Connect Upon connection, the Diva T/A reports the DCE speedCall Control Commands Call Control Commands ATAATH Configuration Commands Configuration Commands Use the default settings AT!V0=nProfile Commands Multilink PPP Commands Multilink PPP Commands Internet Protocol IP Endpoint Discriminator Class/AddressAT%M3=b3c665ac11 Always On / Dynamic Isdn AT Commands Always On / Dynamic Isdn AT Commands AT!X13=n when Bacp is disabled, see Will be opened after the delay specified by AT!X10Default 1000 bytes AT!X14=nDefault values for each setting, and is defined as follows Default AT!X22=nAT!X18 Defined as followsDefault CF PPP over AT!X25=nConnection numbers affects the range ofAT!X21. SeeAT!X21 AT!X26=nUtility Commands Utility Commands Internal TA access command reserved for VUStart or display the Result of a Lapd trace Start or Display the Result of a PPP traceStart an AO/DI X.25 Trace Enter the monitor on the next resetSoft reset the unit and enter the monitor Register Commands AT?Register Commands Analog Device Commands Analog Device Commands AT*FnTo be disabled Disable. Recommended for modem/fax callsEnable with default values default Enable using same terminal endpoint identifier as data portMini-monitor Commands AT Command Result Codes Carrier Connect AT Command Result CodesConnect Protocol Transparent Mode Connect 75T/1200RConnect 1200T/75R Protocol NoneIndex BACP/BOD
Top Page Image Contents