Delta Tau 5xx-603869-xUxx manual AMP1-AMP8 Amplifier connections 1 to, Pin Symbol Function

Page 23

Brick Motion Controller Hardware Reference Manual

AMP1-AMP8: Amplifier connections (1 to 8)

AMP1-AMP8 Amplifier connections			8	7	6	5	4	3	2	1
	(1-8)
	(Female DB-15 Connector)			15	14	13	12	11	10	9
				15	14	13	12	11	10	9
Pin	Symbol	Function	Notes
#	Symbol	Function	Notes
#	DACnA+	Output	DAC A output channel n +
1	DACnA+	Output	DAC A output channel n +
2	DACnB+	Output	DAC B output channel n +
3	AE_NCn+	Output	Amplifier Enable Relay Normally Open channel n +
4	AE_NOn+	Output	Amplifier Enable Relay Normally Closed channel n
5	AFAULTn-	Input	Amplifier Fault channel n -
6	N.C.		No connection
7	N.C.		No connection
8	AGND	Common	Analog Ground
9	DACnA -	Output	DAC A output channel n -
10	DACnB -	Output	DAC B output channel n -
11	AE_COMn	Common	Amplifier Enable Relay Common channel n
12	AFAULTn+	Input	Amplifier Fault channel n +
13	N.C.		No connection
14	AGND	Common	Analog Ground
15	N.C.		No connection

Because the same pinouts are used for all amplifiers, n stands for amplifier number 1 to 8: n=1 / axis 1, n=2 / axis 2, etc.

System Wiring

15

Image 23

Contents 125 Delta Tau Data Systems, Inc. Technical Support Safety InstructionsCopyright Information Operating ConditionsPage Page Revision History Page Table of Contents Brick Motion Controller Hardware Reference Manual Introduction Brick Motion Controller FeaturesBrick Motion Controller Hardware Reference Manual Brick Motion Controller Options Part NumberMacro and Special Feedback Options Analog I/O OptionsCommunication Options Use of Equipment Receiving and UnpackingBrick Motion Controller Hardware Reference Manual Earth Grounding Paths Wiring Earth-GroundNoise Problems X1-X8 Encoder Input 1 to ConnectorsPin Symbol Function X11-12 Analog I/O Ch7 X11 and Ch8 X12, Optional X9/10 Female DB-9 Connector Pin # SymbolX11/12 Female DB-9 Connector Pin # Symbol Function X9-10 Analog I/O Ch5 X9 and Ch6 X10, OptionalX15 Watchdog X13 USB 2.0 ConnectorX14 RJ45, Ethernet Connector Pin # SymbolS2 Firmware Reload Enable TB1 Power ConnectorS1 Re-Initialization on Reset Control Description J4 Limit Inputs 1-4 AxisJ5 Limit Inputs 5-8 Axis Limit and Flag Circuit WiringGND Sample J4/J5, Flags Wiring DiagramsAMP1-AMP8 Amplifier connections 1 to Amplifier Fault / Amplifier Enable diagrams J6 General Purpose I/O J6 General Purpose I/O Female DB-37 Connector Pin # SymbolSourcing Sinking Suggested M-var. # AddressJ7 Extra General Purpose I/O Optional Symbol FunctionSuggested M-var. # Address J8 Extra General Purpose I/O Optional J8 General Purpose I/O Female DB-37 Connector Pin # SymbolSuggested M-var. # Address GBL Sample J6/J7, I/O Wiring DiagramsFunction Pin # Setting up Quadrature EncodersSignal Format Hardware SetupChannel# Address Description Encoder Loss SetupBipolar Setting up the Analog Inputs optionalFiltered DAC Outputs Configuration optional Parameters to Set up Global Hardware Signals Parameters to Set Up Per-Channel Hardware Signals Multi-Channel Servo IC I-Variables Setting up for Pulse and Direction OutputSoftware Setup I7m00 Servo IC m MaxPhase/PWM Frequency ControlI7mn0 Servo IC m Channel n Encoder Decode Control I7mn6 Servo IC m Channel n Output Mode SelectSingle-Channel I-Variables I7m04 PFM Pulse Width ControlIxx31 Motor x Derivative Gain Ixx34 Motor xx Integration ModeIxx30 Motor xx Proportional Gain ExampleBrick Motion Controller Hardware Reference Manual Diagnosing Cause of Watchdog Timer Trip Watchdog TimerActions on Watchdog Timer Trip Troubleshooting Screw Lock Size for all DB-connectors DB- Connector Spacing SpecificationsX1-8 DB-15 Connectors for encoder feedback X9-12 DB-9 Connectors for Analog I/OType of Cable for Encoder Wiring Appendix a Inputs SchematicsJ6 and J7 General Purpose I/O Outputs Opto Gnd PlaneLimits 1,2,3,4 J4 Limit Inputs for AxisLimits 5,6,7,8 J5 Limit Inputs for AxisDimensional Layout and Connector location