Matsushita CF-30CTQAZBM service manual 02F0 CPU ID

Page 16

02D0 System cache error - Cache disabled Contact Panasonic Technical Support.

02F0: CPU ID:

CPU socket number for Multi-Processor error.

02F4: EISA CMOS not writable

ServerBIOS2 test error: Cannot write to EISA CMOS.

02F5: DMA Test Failed

ServerBIOS2 test error: Cannot write to extended DMA (Direct Memory Access) registers.

02F6: Software NMI Failed

ServerBIOS2 test error: Cannot generate software NMI (Non-Maskable Interrupt).

02F7: Fail - Safe Timer NMI Failed

ServerBIOS2 test error: Fail-Safe Timer takes too long.

device address Conflict

Address conflict for specified device.

Allocation Error for: device

Run ISA or EISA Configuration Utility to resolve resource conflict for the specified device.

Failing Bits : nnnn

The hex number nnnn is a map of the bits at the RAM address which failed the memory test. Each 1 (one) in the map indicates a failed bit. See error 230,231 or 232 for offset address of the failure in System, Extended or Shadow memory.

Invalid System Configuration Data

Problem with NVRAM (CMOS) data.

I/O device IRQ conflict

I/O device IRQ conflict error.

Operating System not found

Operating system cannot be located on either drive A: or drive C:. Enter Setup and see if fixed

disk and drive A: are properly identified.

Parity Check 1 nnnn

Parity error found in the system bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????. Parity is a method for checking errors in binary data. A parity error indicates that some data has been corrupted.

Parity Check 2 nnnn

Parity error found in the I/O bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????.

Press <F1> to resume, <F2> to Setup

Displayed after any recoverable error message. Press <F1> to start the boot process or <F2> to enter a Setup and change the settings. Write down and follow the information shown on the screen.

6-2

Image 16

Contents Model No. CF-30CTQAZBM How to replace the fuse For U.K This apparatus must be earthed for your safetyLaser Safety Information Page Page Contents Specifications Model NoAge*20, Recover ProTM 6*20 Only for model with wireless LANOnly for model with Bluetooth You need to install to use the featureNames and Functions of Part E F G Diagram Diagnosis Procedure Troubleshooting Beep signal sound Error message Error Diagnosis by Checking Beep Signal SoundOutline of Post Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Content of the setup is returned to the setting of the user PC-Diagnostic utility End methodSelection of tested device Content of standard test Content of enhancing test Record area frequently accessed All record area is testedTest item Stanard Ty of breakdownContent of Standard Test Content of Extend Test Express Card ConnectorWiring between Super I/O Test ItemWiring Connection Diagram Removing the Battery Pack and HDD Preparation PackBoard Removing the KB Cable Cover and LCD Cable Cover Removing the GPS PCB and Blue- tooth PCBRemoving the Dimm Cover and Bot- tom Cover Removing the USB PCB and AntennaRemoving the PAD PCB Removing the FPC HDD BATRemoving the Main PCB MP PCB Remove the 4 Screws. N14 PCBRemoving the Handle and Power SW Removing the Display Unit Removing the LCD Rear Cabinet Hinge L and RRemoving the Inverter PCB, TS PCB and LCD Unit Removing the Antenna PCB L and RSetting the Antenna PCB L and R Screws N2 DRHM5054XA Arranging the Antenna L and R CablesSetting the Inverter PCB, TS PCB and LCD Unit Preparation of InverterSetting the LCD Rear Cabinet, Hinge L and R Assembly of LCD UnitSetting the Display Unit Setting the Handle and Power SWAttach the Power LED Packing Sheet to the LED Spacer Fix the SW LED PCB using the Screw. N5Fix the Palm Top Cover using the 5 Screws. N4 No1 to Set the SW LED PCBAssembly of Power SW Assembly of Palm Top CoverSetting the I/O PCB Setting the SD PCB, Express Card Setting the Main PCB Connect the 2 Cables to the 2 Connectors. CN17,CN27Fix the Screw. N7 Attach the TOP Screws Assembly of LAN, Modem and MDC Assembly of Main PCBSetting the PAD PCB Assembly of PAD PCBSetting the FPC HDD BAT Preparation of HDD FPC AssyDirection C View Tighten Setting the USB PCB and Antenna PCB Assembly of USB PCB and Antenna PCB Setting the Dimm Cover and Bottom Cover Preparation of Dimm Cover Setting the GPS PCB and Bluetooth PCB Screws N11 DFHE5025XA Screws N12 DXQT2+F3FNLSetting the KB Cable Cover, Keyboard and LCD Cable Cover Arranging the KeyboardSetting the HDD Screws N2 DRHM5054XA Screws N5 DRQT26+D4FKLPreparation oh HDD Assy HDD FPC Ass’yPush and bend HDD Thermal Plate SEC Page Setting the Battery Pack and HDD Pack Set the HDD Pack Set the Battery PackXploded View 18 + 0.22 N.m + 0.2 kgf.cm 2 + 0.02 N.m 10-1CF-30CTQAZBM 10-219 + 0.02 N.m 216 + 0.0196 N.m314 + 0.0196 N.m 441 + 0.049 N.m10-4 45 + 0.50 N.m 10-510-6 10-7 Replacement Parts List Comparison Table