Matsushita CF-30CTQAZBM Setting the LCD Rear Cabinet, Hinge L and R, Assembly of LCD Unit

Page 35

QAssembly of LCD Unit

* Notes:

1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2

Confirm that the LCD

Cushion is not wrapped.

Attach the Inverter MIL Shierd

Match to the LCD edge and attach it.

Clearance : 2 mm or less

0 0.5mm

Attach the TS Controller

LCD Drop Holder Insertion

LCD Front Ass’y

LCD Drop Holder Insertion

Flex Stiffening Plate Edge
	Release Paper B
TS Flex Insertion
	Release Paper A
Attach the Tape	Release Paper C
Attach the Tape

* Notes:

1.Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm

1.Insert the TS Flex into the TS Controller, and attach the tape.

2.Remove the Release Paper A and attach the TS Controller. (Do not come off the sheet and apply the pressure on the LCD.)

3.Remove the Release Paper B and attach it on the TS Controller.

4.Remove the Release Paper C and attach it on the LCD.

9.2.4. Setting the LCD Rear Cabinet, Hinge L and R

1.Fix the Hinge L and R using the 2 Screws. <K9-1-4>

2.Set the LCD Latch.

3.Fix the LCD Rear Cabinet using the 4 Screws. <N7> No1 to No4

4.Fix the left and right LCD Cover Side Cover using the 4 Screws <N7> and 2 Screws. <N13>

5.Fix the 2 Wireless Antenna Corner Cover using the 4 Screws. <N7>

Note:

Tighten the Screws in the numbered order (No1 to No4).

Screws <N2>: DRHM5054XA

Screws <N7>: DRSB26+10HKL

Screws <N13>: DRSB4+10FKL

Screws <K9-1-4>: DRYN4+J10KLT

left LCD Cover <N7> <N13>
Side Cover<N7>	No.1
<N7>	<N7>	LCD Rear Cabinet
<N7>		No.4
<N7>		No.4
<N7>		<N7>
		<N7>
No.3
<N7> No.2		<N13>
<N7>		<N7>
		<N7>
Wireless Antenna		<N7>
Wireless Antenna
Corner Cover		<N7>
		<N7>
LCD Latch	<N7>
<K9-1-4>		right LCD Cover
Hinge L		Side Cover

Wireless Antenna

Corner Cover

<K9-1-4>

Hinge R

LCD Front Cabinet

9-13

Image 35

Contents

Model No. CF-30CTQAZBM For U.K This apparatus must be earthed for your safety How to replace the fuseLaser Safety Information Page Page Contents Model No SpecificationsYou need to install to use the feature Age*20, Recover ProTM 6*20Only for model with wireless LAN Only for model with BluetoothNames and Functions of Part E F G Diagram Diagnosis Procedure Troubleshooting Outline of Post Error Diagnosis by Checking Beep Signal SoundBeep signal sound Error message Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device PC-Diagnostic utility End methodContent of the setup is returned to the setting of the user Ty of breakdown Content of standard test Content of enhancing testRecord area frequently accessed All record area is tested Test item StanardTest Item Content of Standard Test Content of Extend TestExpress Card Connector Wiring between Super I/OWiring Connection Diagram Preparation Pack Removing the Battery Pack and HDDBoard Removing the GPS PCB and Blue- tooth PCB Removing the KB Cable Cover and LCD Cable CoverRemoving the USB PCB and Antenna Removing the Dimm Cover and Bot- tom CoverRemoving the Main PCB Removing the FPC HDD BATRemoving the PAD PCB MP PCB PCB Remove the 4 Screws. N14Removing the Handle and Power SW Hinge L and R Removing the Display Unit Removing the LCD Rear CabinetRemoving the Antenna PCB L and R Removing the Inverter PCB, TS PCB and LCD UnitScrews N2 DRHM5054XA Arranging the Antenna L and R Cables Setting the Antenna PCB L and RPreparation of Inverter Setting the Inverter PCB, TS PCB and LCD UnitAssembly of LCD Unit Setting the LCD Rear Cabinet, Hinge L and RSetting the Handle and Power SW Setting the Display UnitSet the SW LED PCB Attach the Power LED Packing Sheet to the LED SpacerFix the SW LED PCB using the Screw. N5 Fix the Palm Top Cover using the 5 Screws. N4 No1 toAssembly of Palm Top Cover Assembly of Power SWSetting the I/O PCB Setting the SD PCB, Express Card Connect the 2 Cables to the 2 Connectors. CN17,CN27 Setting the Main PCBFix the Screw. N7 Attach the TOP Screws Assembly of Main PCB Assembly of LAN, Modem and MDCAssembly of PAD PCB Setting the PAD PCBPreparation of HDD FPC Assy Setting the FPC HDD BATDirection C View Tighten Setting the USB PCB and Antenna PCB Assembly of USB PCB and Antenna PCB Setting the Dimm Cover and Bottom Cover Preparation of Dimm Cover Screws N11 DFHE5025XA Screws N12 DXQT2+F3FNL Setting the GPS PCB and Bluetooth PCBArranging the Keyboard Setting the KB Cable Cover, Keyboard and LCD Cable CoverScrews N2 DRHM5054XA Screws N5 DRQT26+D4FKL Setting the HDDHDD FPC Ass’y Preparation oh HDD AssyPush and bend HDD Thermal Plate SEC Page Set the HDD Pack Set the Battery Pack Setting the Battery Pack and HDD Pack18 + 0.22 N.m + 0.2 kgf.cm 2 + 0.02 N.m 10-1 Xploded View10-2 CF-30CTQAZBM441 + 0.049 N.m 19 + 0.02 N.m216 + 0.0196 N.m 314 + 0.0196 N.m10-4 10-5 45 + 0.50 N.m10-6 10-7 Replacement Parts List Comparison Table