Matsushita CF-30CTQAZBM service manual Fix the Screw. N7 Attach the TOP Screws

Page 41

24.Fix the Screw. <N7>

25.Attach the TOP Screws.

TOP Screw Sheet

<N7>

Connector (CN17)

Note:

Connector (CN27)

Tighten the Screws in the numbered order (No1 to No8). Tighten the Screws in the numbered order (No1 to No6).

Screws <N5>: DRQT26+D4FKL

Screws <N7>: DRSB26+10HKL

Screws <N11>: DFHE5025XA

Screws <N16>: DRQT26+E5FKL

Screws <N17>: DRQT26+E6FKL

Screws <N18>: DRSB26+8FKL

Screws <N21>: DXQT2+E12FNL

9-19

Image 41
Contents Model No. CF-30CTQAZBM For U.K This apparatus must be earthed for your safety How to replace the fuseLaser Safety Information Page Page Contents Model No SpecificationsOnly for model with wireless LAN Age*20, Recover ProTM 6*20Only for model with Bluetooth You need to install to use the featureNames and Functions of Part E F G Diagram Diagnosis Procedure Troubleshooting Outline of Post Error Diagnosis by Checking Beep Signal SoundBeep signal sound Error message Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device PC-Diagnostic utility End methodContent of the setup is returned to the setting of the user Record area frequently accessed All record area is tested Content of standard test Content of enhancing testTest item Stanard Ty of breakdownExpress Card Connector Content of Standard Test Content of Extend TestWiring between Super I/O Test ItemWiring Connection Diagram Preparation Pack Removing the Battery Pack and HDDBoard Removing the GPS PCB and Blue- tooth PCB Removing the KB Cable Cover and LCD Cable CoverRemoving the USB PCB and Antenna Removing the Dimm Cover and Bot- tom CoverRemoving the Main PCB Removing the FPC HDD BATRemoving the PAD PCB MP PCB PCB Remove the 4 Screws. N14Removing the Handle and Power SW Hinge L and R Removing the Display Unit Removing the LCD Rear CabinetRemoving the Antenna PCB L and R Removing the Inverter PCB, TS PCB and LCD UnitScrews N2 DRHM5054XA Arranging the Antenna L and R Cables Setting the Antenna PCB L and RPreparation of Inverter Setting the Inverter PCB, TS PCB and LCD UnitAssembly of LCD Unit Setting the LCD Rear Cabinet, Hinge L and RSetting the Handle and Power SW Setting the Display UnitFix the SW LED PCB using the Screw. N5 Attach the Power LED Packing Sheet to the LED SpacerFix the Palm Top Cover using the 5 Screws. N4 No1 to Set the SW LED PCBAssembly of Palm Top Cover Assembly of Power SWSetting the I/O PCB Setting the SD PCB, Express Card Connect the 2 Cables to the 2 Connectors. CN17,CN27 Setting the Main PCBFix the Screw. N7 Attach the TOP Screws Assembly of Main PCB Assembly of LAN, Modem and MDCAssembly of PAD PCB Setting the PAD PCBPreparation of HDD FPC Assy Setting the FPC HDD BATDirection C View Tighten Setting the USB PCB and Antenna PCB Assembly of USB PCB and Antenna PCB Setting the Dimm Cover and Bottom Cover Preparation of Dimm Cover Screws N11 DFHE5025XA Screws N12 DXQT2+F3FNL Setting the GPS PCB and Bluetooth PCBArranging the Keyboard Setting the KB Cable Cover, Keyboard and LCD Cable CoverScrews N2 DRHM5054XA Screws N5 DRQT26+D4FKL Setting the HDDHDD FPC Ass’y Preparation oh HDD AssyPush and bend HDD Thermal Plate SEC Page Set the HDD Pack Set the Battery Pack Setting the Battery Pack and HDD Pack18 + 0.22 N.m + 0.2 kgf.cm 2 + 0.02 N.m 10-1 Xploded View10-2 CF-30CTQAZBM216 + 0.0196 N.m 19 + 0.02 N.m314 + 0.0196 N.m 441 + 0.049 N.m10-4 10-5 45 + 0.50 N.m10-6 10-7 Replacement Parts List Comparison Table