Matsushita CF-30CTQAZBM service manual Setting the GPS PCB and Bluetooth PCB

Page 50

9.2.15. Setting the GPS PCB and Bluetooth PCB

1.Fix the GPS BT Angle and GPS PCB using the 2 Screws. <N11>

2.Connect the Cable to the Connector on GPS PCB.

3.Fix the GPS Ass’y using the 4 Screws. <N12>

4.Connect the Cable to the Connector. (CN25)

	<N12>
<N12>	<N12> GPS BT Angle
	<N12> GPS BT Angle
	<N12>

Screws <N11>: DFHE5025XA

Screws <N12>: DXQT2+F3FNL

GPS PCB

<N11>

<N11>

Bluetooth

PCB

Connector(CN25)

to Connector (CN25)

QCautions for Setting GPS ASSY and BT PCB ASSY

* Notes:

* Notes:

1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2

1. Do not gouge when inserting and removing the plug.

2. Do not damage the coating when handling the cable.

Safety Working

Attach the Tape

Fit to the plate squeeze line. 1

Process the wire of whip ANT cable from

LCD to the back from the aperture.

Whip Antenna Cable

8

1

Put the Cable along

the Cabinet side and

tape it firmly.

Main Antenna

Process the wire to the

Sub Antenna

10

2

back from the aperture.

Match to the boss center.

Insert the

Bluetooth Cable

cable plug.

Cabinet Level Standard

Pass the Cable behind

the Cabinet protrusion.

Tolerance 0 to 1

GPS Antenna

Process the wire into the groove.

Safety Working

Connect into the coaxial Connector.

Attach the Cable Sheet into

Attach the Cable Sheet into

Main Cable and Whip Cable.

0 2

Safety Working

Sub Cable and GPS Cable.

Ensure that the wrapping

Avoid coming over the groove.

direction is right.

Bluet

ooth Cable

0

2

Ensure that the wrapping

direction is right.

Whip Antenna Cable

Main Antenna Cable

Sub Antenna Cable

GPS Antenna Cable

9-28

Image 50

Contents Model No. CF-30CTQAZBM How to replace the fuse For U.K This apparatus must be earthed for your safetyLaser Safety Information Page Page Contents Specifications Model NoOnly for model with Bluetooth Age*20, Recover ProTM 6*20Only for model with wireless LAN You need to install to use the featureNames and Functions of Part E F G Diagram Diagnosis Procedure Troubleshooting Outline of Post Error Diagnosis by Checking Beep Signal SoundBeep signal sound Error message Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device PC-Diagnostic utility End methodContent of the setup is returned to the setting of the user Test item Stanard Content of standard test Content of enhancing testRecord area frequently accessed All record area is tested Ty of breakdownWiring between Super I/O Content of Standard Test Content of Extend TestExpress Card Connector Test ItemWiring Connection Diagram Removing the Battery Pack and HDD Preparation PackBoard Removing the KB Cable Cover and LCD Cable Cover Removing the GPS PCB and Blue- tooth PCBRemoving the Dimm Cover and Bot- tom Cover Removing the USB PCB and AntennaRemoving the Main PCB Removing the FPC HDD BATRemoving the PAD PCB MP PCB Remove the 4 Screws. N14 PCBRemoving the Handle and Power SW Removing the Display Unit Removing the LCD Rear Cabinet Hinge L and RRemoving the Inverter PCB, TS PCB and LCD Unit Removing the Antenna PCB L and RSetting the Antenna PCB L and R Screws N2 DRHM5054XA Arranging the Antenna L and R CablesSetting the Inverter PCB, TS PCB and LCD Unit Preparation of InverterSetting the LCD Rear Cabinet, Hinge L and R Assembly of LCD UnitSetting the Display Unit Setting the Handle and Power SWFix the Palm Top Cover using the 5 Screws. N4 No1 to Attach the Power LED Packing Sheet to the LED SpacerFix the SW LED PCB using the Screw. N5 Set the SW LED PCBAssembly of Power SW Assembly of Palm Top CoverSetting the I/O PCB Setting the SD PCB, Express Card Setting the Main PCB Connect the 2 Cables to the 2 Connectors. CN17,CN27Fix the Screw. N7 Attach the TOP Screws Assembly of LAN, Modem and MDC Assembly of Main PCBSetting the PAD PCB Assembly of PAD PCBSetting the FPC HDD BAT Preparation of HDD FPC AssyDirection C View Tighten Setting the USB PCB and Antenna PCB Assembly of USB PCB and Antenna PCB Setting the Dimm Cover and Bottom Cover Preparation of Dimm Cover Setting the GPS PCB and Bluetooth PCB Screws N11 DFHE5025XA Screws N12 DXQT2+F3FNLSetting the KB Cable Cover, Keyboard and LCD Cable Cover Arranging the KeyboardSetting the HDD Screws N2 DRHM5054XA Screws N5 DRQT26+D4FKLPreparation oh HDD Assy HDD FPC Ass’yPush and bend HDD Thermal Plate SEC Page Setting the Battery Pack and HDD Pack Set the HDD Pack Set the Battery PackXploded View 18 + 0.22 N.m + 0.2 kgf.cm 2 + 0.02 N.m 10-1CF-30CTQAZBM 10-2314 + 0.0196 N.m 19 + 0.02 N.m216 + 0.0196 N.m 441 + 0.049 N.m10-4 45 + 0.50 N.m 10-510-6 10-7 Replacement Parts List Comparison Table