Matsushita CF-30CTQAZBM service manual Removing the Battery Pack and HDD, Preparation Pack

Page 23

9Disassembly/Reassembly

Note:

Power off the computer. Do not shut down to the Suspend or hibernation mode.

Do not add peripherals while the computer is in the Suspend or hibernation mode; abnormal operation may result.

9.1.	Disassembly Instructions	9.1.2. Removing the Battery Pack and HDD
9.1.1.	Preparation	Pack
9.1.1.	Preparation

Before disassembling, be sure to make the following prepara- tions.

•Shut down Windows and turn off the power.

•Disconnect the AC adaptor.

•Remove the optional DIMM memory card and PCMCIA card if they are connected.

•Remove other devices if they are connected.

Attention:

•Please execute writing BIOS ID when you exchange the Main Board.

•Parts (Sheet and rubber) etc. related various the Conductive Cloth and Heat Spreader cannot be recycled. Use new parts.

Battery Cover

HDD Cover

Battery Pack

HDD Pack

1.Open the Battery Cover.

2.Remove the Battery Pack.

3.Open the HDD Cover.

4.Remove the HDD Pack.

9-1

Image 23

Contents Model No. CF-30CTQAZBM For U.K This apparatus must be earthed for your safety How to replace the fuseLaser Safety Information Page Page Contents Model No SpecificationsYou need to install to use the feature Age*20, Recover ProTM 6*20Only for model with wireless LAN Only for model with BluetoothNames and Functions of Part E F G Diagram Diagnosis Procedure Troubleshooting Outline of Post Error Diagnosis by Checking Beep Signal SoundBeep signal sound Error message Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device PC-Diagnostic utility End methodContent of the setup is returned to the setting of the user Ty of breakdown Content of standard test Content of enhancing testRecord area frequently accessed All record area is tested Test item StanardTest Item Content of Standard Test Content of Extend TestExpress Card Connector Wiring between Super I/OWiring Connection Diagram Preparation Pack Removing the Battery Pack and HDDBoard Removing the GPS PCB and Blue- tooth PCB Removing the KB Cable Cover and LCD Cable CoverRemoving the USB PCB and Antenna Removing the Dimm Cover and Bot- tom CoverRemoving the Main PCB Removing the FPC HDD BATRemoving the PAD PCB MP PCB PCB Remove the 4 Screws. N14Removing the Handle and Power SW Hinge L and R Removing the Display Unit Removing the LCD Rear CabinetRemoving the Antenna PCB L and R Removing the Inverter PCB, TS PCB and LCD UnitScrews N2 DRHM5054XA Arranging the Antenna L and R Cables Setting the Antenna PCB L and RPreparation of Inverter Setting the Inverter PCB, TS PCB and LCD UnitAssembly of LCD Unit Setting the LCD Rear Cabinet, Hinge L and RSetting the Handle and Power SW Setting the Display UnitSet the SW LED PCB Attach the Power LED Packing Sheet to the LED SpacerFix the SW LED PCB using the Screw. N5 Fix the Palm Top Cover using the 5 Screws. N4 No1 toAssembly of Palm Top Cover Assembly of Power SWSetting the I/O PCB Setting the SD PCB, Express Card Connect the 2 Cables to the 2 Connectors. CN17,CN27 Setting the Main PCBFix the Screw. N7 Attach the TOP Screws Assembly of Main PCB Assembly of LAN, Modem and MDCAssembly of PAD PCB Setting the PAD PCBPreparation of HDD FPC Assy Setting the FPC HDD BATDirection C View Tighten Setting the USB PCB and Antenna PCB Assembly of USB PCB and Antenna PCB Setting the Dimm Cover and Bottom Cover Preparation of Dimm Cover Screws N11 DFHE5025XA Screws N12 DXQT2+F3FNL Setting the GPS PCB and Bluetooth PCBArranging the Keyboard Setting the KB Cable Cover, Keyboard and LCD Cable CoverScrews N2 DRHM5054XA Screws N5 DRQT26+D4FKL Setting the HDDHDD FPC Ass’y Preparation oh HDD AssyPush and bend HDD Thermal Plate SEC Page Set the HDD Pack Set the Battery Pack Setting the Battery Pack and HDD Pack18 + 0.22 N.m + 0.2 kgf.cm 2 + 0.02 N.m 10-1 Xploded View10-2 CF-30CTQAZBM441 + 0.049 N.m 19 + 0.02 N.m216 + 0.0196 N.m 314 + 0.0196 N.m10-4 10-5 45 + 0.50 N.m10-6 10-7 Replacement Parts List Comparison Table