Matsushita CF-30CTQAZBM Selection of tested device, PC-Diagnostic utility End method

Page 19

2-1. Selection of tested device

-To test only a specific device, "Test" and "Do not test" of each device can be selected.

-The device which can select the enhancing test changes in order of "The standard is tested" and "Do not test" whenever the device icon is clicked.

Start the standard test

Do not test

Please begin testing clicking if the selection of the tested device ends.

2-2. "PC-Diagnostic utility" End method

When of "Close" on the right of the screen is clicked, the computer reactivates automatically. Or, the power supply switch is done in the slide and the power supply is turned off.

2-3. The content of the setup is returned to the setting of the user

1.Turned on the computer.

2."F2" is pushed on the screen while "Press<F2>to enter Setup" is displayed of "Panasonic".

3.Push "F10", and on the screen of "Is the change in the setting preserved and do end?"and then "Yes" is selected, and "Enter" is pushed.

4.The computer reactivates automatically.

5.The end option is chosen by the start menu, and the power supply of the computer is turned off.

Standard at test time

 

All devices other than RAM and HDD

about 1 minute

RAM standard test

1 - 2 minutes

HDD standard test

2 - 3 minutes

HDD enhancing test (60GB)

about 40 minutes

Ex.The standard when the standard <all device> is tested becomes 1+2+3=6 minutes.

There is greatly a difference from RAM test when the memory is increased according to the perform- ance of the memory occasionally.

Moreover, when the main body of PC under the test is a high temperature, it occasionally takes time.

There is greatly a difference from HDD according to the performance of the drive occasionally.

7-3

Image 19
Contents Model No. CF-30CTQAZBM For U.K This apparatus must be earthed for your safety How to replace the fuseLaser Safety Information Page Page Contents Model No SpecificationsYou need to install to use the feature Age*20, Recover ProTM 6*20Only for model with wireless LAN Only for model with BluetoothNames and Functions of Part E F G Diagram Diagnosis Procedure Troubleshooting Beep signal sound Error message Error Diagnosis by Checking Beep Signal SoundOutline of Post Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Content of the setup is returned to the setting of the user PC-Diagnostic utility End methodSelection of tested device Ty of breakdown Content of standard test Content of enhancing testRecord area frequently accessed All record area is tested Test item StanardTest Item Content of Standard Test Content of Extend TestExpress Card Connector Wiring between Super I/OWiring Connection Diagram Preparation Pack Removing the Battery Pack and HDDBoard Removing the GPS PCB and Blue- tooth PCB Removing the KB Cable Cover and LCD Cable CoverRemoving the USB PCB and Antenna Removing the Dimm Cover and Bot- tom CoverRemoving the PAD PCB Removing the FPC HDD BATRemoving the Main PCB MP PCB PCB Remove the 4 Screws. N14Removing the Handle and Power SW Hinge L and R Removing the Display Unit Removing the LCD Rear CabinetRemoving the Antenna PCB L and R Removing the Inverter PCB, TS PCB and LCD UnitScrews N2 DRHM5054XA Arranging the Antenna L and R Cables Setting the Antenna PCB L and RPreparation of Inverter Setting the Inverter PCB, TS PCB and LCD UnitAssembly of LCD Unit Setting the LCD Rear Cabinet, Hinge L and RSetting the Handle and Power SW Setting the Display UnitSet the SW LED PCB Attach the Power LED Packing Sheet to the LED SpacerFix the SW LED PCB using the Screw. N5 Fix the Palm Top Cover using the 5 Screws. N4 No1 toAssembly of Palm Top Cover Assembly of Power SWSetting the I/O PCB Setting the SD PCB, Express Card Connect the 2 Cables to the 2 Connectors. CN17,CN27 Setting the Main PCBFix the Screw. N7 Attach the TOP Screws Assembly of Main PCB Assembly of LAN, Modem and MDCAssembly of PAD PCB Setting the PAD PCBPreparation of HDD FPC Assy Setting the FPC HDD BATDirection C View Tighten Setting the USB PCB and Antenna PCB Assembly of USB PCB and Antenna PCB Setting the Dimm Cover and Bottom Cover Preparation of Dimm Cover Screws N11 DFHE5025XA Screws N12 DXQT2+F3FNL Setting the GPS PCB and Bluetooth PCBArranging the Keyboard Setting the KB Cable Cover, Keyboard and LCD Cable CoverScrews N2 DRHM5054XA Screws N5 DRQT26+D4FKL Setting the HDDHDD FPC Ass’y Preparation oh HDD AssyPush and bend HDD Thermal Plate SEC Page Set the HDD Pack Set the Battery Pack Setting the Battery Pack and HDD Pack18 + 0.22 N.m + 0.2 kgf.cm 2 + 0.02 N.m 10-1 Xploded View10-2 CF-30CTQAZBM441 + 0.049 N.m 19 + 0.02 N.m216 + 0.0196 N.m 314 + 0.0196 N.m10-4 10-5 45 + 0.50 N.m10-6 10-7 Replacement Parts List Comparison Table