Matsushita CF-30CTQAZBM service manual

Page 57

HDD Ass’y insertion

NG

Set the CN side first, and then set the

TAB side pushing to the A direction.

SATA Guide Set

SATA Guard is installed

A

Insert to make the Cushion on the HDD inside of the Cushion on the lower case.

Avoid getting HDD under the side damper when inserting HDD

* Notes:

1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2

Tighten of

Screw

Tighten of

ScrewTighten of

Screw

Tighten of

Screw

Confirm that the CN board moves up/down and right/left after assembling.

Order of fixing

ScrewScrewScrewScrew

Tighten of Screw

5 2

7 2

Attach the Edition Number Label

Label Letters : head is top

9-35

Image 57

Contents Model No. CF-30CTQAZBM For U.K This apparatus must be earthed for your safety How to replace the fuseLaser Safety Information Page Page Contents Model No SpecificationsOnly for model with wireless LAN Age*20, Recover ProTM 6*20Only for model with Bluetooth You need to install to use the featureNames and Functions of Part E F G Diagram Diagnosis Procedure Troubleshooting Error Diagnosis by Checking Beep Signal Sound Beep signal sound Error messageOutline of Post Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility PC-Diagnostic utility End method Content of the setup is returned to the setting of the userSelection of tested device Record area frequently accessed All record area is tested Content of standard test Content of enhancing testTest item Stanard Ty of breakdownExpress Card Connector Content of Standard Test Content of Extend TestWiring between Super I/O Test ItemWiring Connection Diagram Preparation Pack Removing the Battery Pack and HDDBoard Removing the GPS PCB and Blue- tooth PCB Removing the KB Cable Cover and LCD Cable CoverRemoving the USB PCB and Antenna Removing the Dimm Cover and Bot- tom CoverRemoving the FPC HDD BAT Removing the PAD PCBRemoving the Main PCB MP PCB PCB Remove the 4 Screws. N14Removing the Handle and Power SW Hinge L and R Removing the Display Unit Removing the LCD Rear CabinetRemoving the Antenna PCB L and R Removing the Inverter PCB, TS PCB and LCD UnitScrews N2 DRHM5054XA Arranging the Antenna L and R Cables Setting the Antenna PCB L and RPreparation of Inverter Setting the Inverter PCB, TS PCB and LCD UnitAssembly of LCD Unit Setting the LCD Rear Cabinet, Hinge L and RSetting the Handle and Power SW Setting the Display UnitFix the SW LED PCB using the Screw. N5 Attach the Power LED Packing Sheet to the LED SpacerFix the Palm Top Cover using the 5 Screws. N4 No1 to Set the SW LED PCBAssembly of Palm Top Cover Assembly of Power SWSetting the I/O PCB Setting the SD PCB, Express Card Connect the 2 Cables to the 2 Connectors. CN17,CN27 Setting the Main PCBFix the Screw. N7 Attach the TOP Screws Assembly of Main PCB Assembly of LAN, Modem and MDCAssembly of PAD PCB Setting the PAD PCBPreparation of HDD FPC Assy Setting the FPC HDD BATDirection C View Tighten Setting the USB PCB and Antenna PCB Assembly of USB PCB and Antenna PCB Setting the Dimm Cover and Bottom Cover Preparation of Dimm Cover Screws N11 DFHE5025XA Screws N12 DXQT2+F3FNL Setting the GPS PCB and Bluetooth PCBArranging the Keyboard Setting the KB Cable Cover, Keyboard and LCD Cable CoverScrews N2 DRHM5054XA Screws N5 DRQT26+D4FKL Setting the HDDHDD FPC Ass’y Preparation oh HDD AssyPush and bend HDD Thermal Plate SEC Page Set the HDD Pack Set the Battery Pack Setting the Battery Pack and HDD Pack18 + 0.22 N.m + 0.2 kgf.cm 2 + 0.02 N.m 10-1 Xploded View10-2 CF-30CTQAZBM216 + 0.0196 N.m 19 + 0.02 N.m314 + 0.0196 N.m 441 + 0.049 N.m10-4 10-5 45 + 0.50 N.m10-6 10-7 Replacement Parts List Comparison Table