Matsushita CF-30CTQAZBM Setting the Inverter PCB, TS PCB and LCD Unit, Preparation of Inverter

Page 34

9.2.3. Setting the Inverter PCB, TS PCB and LCD Unit

1.Set the LCD Unit to the LCD Front Cabinet in order.

2.Attach the 2 drop holders.

3.Connect the Cable to the Connector. (CN200,CN201)

4.Connect the 3 Cables to the 3 Connectors.

5.Fix the Inverter PCB using the 2 Screws. <N5>

Screws <N5>: DRQT26+D4FKL

C

LCD Drop Holder

Connector

(CN201) Connector (CN200)

TS PCB

LCD Drop

A B Holder

LCD Unit	Inverter PCB
	<N5>

C

B <N5>

A

LCD Front Cabinet

to Connector (CN200)

QPreparation of Inverter

* Notes:

1.Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2

2.When handling Inverter-PCB, do not bend or add impact.

Safety Working

			Important Parts
			for Safety
			Inverter-PCB
Do not touch the Transformer part			Inverter-PCB
when attaching to Inverter Case.
		Check the part
		number ’2148M1’

Inverter Shield Case

Prepare Inverter and the Inverter shield Case Outside for Assysite.

Inverter Shield Case Outside

Wrap Inverter Shield Tape around Inverter Shield Case and attach.

Ensure that Inverter Shield Tape does not run over the edge of Inverter Shield Case.

		Inverter is set,	Inverter Shield Case is set
		Inverter is set,	Attach the Inverter Shield Tape
		attach
	Board attachment

<Inverter Shield Tapes Attachment Guide> Protrusion by wrinkles, etc. = 0.2 or less Air Bubble = 1 cm 2 or less / 1 bubble size

Attach it putting the protrusion mark next to the caution label.

Match the board edge and the case edge.

Difference: 0.5mm or less

9-12

Image 34

Contents

Model No. CF-30CTQAZBM How to replace the fuse For U.K This apparatus must be earthed for your safetyLaser Safety Information Page Page Contents Specifications Model NoOnly for model with Bluetooth Age*20, Recover ProTM 6*20Only for model with wireless LAN You need to install to use the featureNames and Functions of Part E F G Diagram Diagnosis Procedure Troubleshooting Beep signal sound Error message Error Diagnosis by Checking Beep Signal SoundOutline of Post Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Content of the setup is returned to the setting of the user PC-Diagnostic utility End methodSelection of tested device Test item Stanard Content of standard test Content of enhancing testRecord area frequently accessed All record area is tested Ty of breakdownWiring between Super I/O Content of Standard Test Content of Extend TestExpress Card Connector Test ItemWiring Connection Diagram Removing the Battery Pack and HDD Preparation PackBoard Removing the KB Cable Cover and LCD Cable Cover Removing the GPS PCB and Blue- tooth PCBRemoving the Dimm Cover and Bot- tom Cover Removing the USB PCB and AntennaRemoving the PAD PCB Removing the FPC HDD BATRemoving the Main PCB MP PCB Remove the 4 Screws. N14 PCB Removing the Handle and Power SW Removing the Display Unit Removing the LCD Rear Cabinet Hinge L and RRemoving the Inverter PCB, TS PCB and LCD Unit Removing the Antenna PCB L and RSetting the Antenna PCB L and R Screws N2 DRHM5054XA Arranging the Antenna L and R CablesSetting the Inverter PCB, TS PCB and LCD Unit Preparation of InverterSetting the LCD Rear Cabinet, Hinge L and R Assembly of LCD UnitSetting the Display Unit Setting the Handle and Power SWFix the Palm Top Cover using the 5 Screws. N4 No1 to Attach the Power LED Packing Sheet to the LED SpacerFix the SW LED PCB using the Screw. N5 Set the SW LED PCBAssembly of Power SW Assembly of Palm Top CoverSetting the I/O PCB Setting the SD PCB, Express Card Setting the Main PCB Connect the 2 Cables to the 2 Connectors. CN17,CN27Fix the Screw. N7 Attach the TOP Screws Assembly of LAN, Modem and MDC Assembly of Main PCBSetting the PAD PCB Assembly of PAD PCBSetting the FPC HDD BAT Preparation of HDD FPC AssyDirection C View Tighten Setting the USB PCB and Antenna PCB Assembly of USB PCB and Antenna PCB Setting the Dimm Cover and Bottom Cover Preparation of Dimm Cover Setting the GPS PCB and Bluetooth PCB Screws N11 DFHE5025XA Screws N12 DXQT2+F3FNLSetting the KB Cable Cover, Keyboard and LCD Cable Cover Arranging the KeyboardSetting the HDD Screws N2 DRHM5054XA Screws N5 DRQT26+D4FKLPreparation oh HDD Assy HDD FPC Ass’yPush and bend HDD Thermal Plate SEC Page Setting the Battery Pack and HDD Pack Set the HDD Pack Set the Battery PackXploded View 18 + 0.22 N.m + 0.2 kgf.cm 2 + 0.02 N.m 10-1CF-30CTQAZBM 10-2314 + 0.0196 N.m 19 + 0.02 N.m216 + 0.0196 N.m 441 + 0.049 N.m10-4 45 + 0.50 N.m 10-510-6 10-7 Replacement Parts List Comparison Table