Matsushita CF-30CTQAZBM service manual Assembly of Power SW, Assembly of Palm Top Cover

Page 38

QAssembly of Power SW

	Attach the Battery Cushion
Battery Pack Insertion Slot
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
			12	2
3	5	25	2
3	5
Tighten of Screw
FPC Power SW is set	Attach the Battery Slide Sheet (on Battery Cushion)
FPC Power SW is set
Power SW LED	Avoid air leaking into it. Avoid coming off 4 corners.
Panel is set	Avoid air leaking into it. Avoid coming off 4 corners.
	Fit to the line.
	10	1

Attach the DC Gasket

Ensure the upper and lower Flex holes match.

Top

Connection Direction

Bottom

Cable Power

Connection

CAB Wall

Connection Direction

Safety Working

Attach the TP

FPC Tape

Match the Cabinet slit and the tape slit.

Do not run the Cabinet edge out of the tape slit.

QAssembly of Palm Top Cover

Using the pressure jig, Ensure the loads are applied equally.

Make sure the adhesive materials are attached closely on the whole side.

Process the speaker lead wire not to put inside when applying the load.

Avoid running over the protrusion attached to the protrusion side of the upper Cabinet.

Attach the Pad

A

B

Ensure that the PAD and the button neck are attached with adhesive firmly.

Insert FPC into the hole	Touch Pad SW Knob
of upper cabinet.	Rubber is set

	Order of fixing
	Screw	Screw	Screw
	Screw	Screw
	Note: Separation		Tighten of
			Tighten of
			Screw
Touch Pad SW Knob			Tighten of
In is set			Screw

Notes for Separation

Tighten of

ScrewTighten of

Screw

Tighten of

Screw

Put to the arrow direction and attach it.

Protrusion

Attach the TP

Bottom Tape

Do not come over the Pad edge.

Attach the

PWB 6LED

Put to the left and set.

Palm Top Cover is set

Do not attach the oil on both sides. Avoid running over!

Attach the Pad WP Sheet

Attach within the range of the upper Cabinet concave.

Attach the Washer (See below)

LEDX6 Spacer	Insert FFC into the hole		Notes:
	of upper cabinet.
Sheet is set
			After attaching, trace around TP,

FFC 6LED is set			SW and circumference with finger.

1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2

Palm Top

Cover

Attach the Washer

Attach it not to cover the hole of LEDX6 Spacer Sheet.

Palmtop Preparation

9-16

Image 38

Contents Model No. CF-30CTQAZBM How to replace the fuse For U.K This apparatus must be earthed for your safetyLaser Safety Information Page Page Contents Specifications Model NoOnly for model with Bluetooth Age*20, Recover ProTM 6*20Only for model with wireless LAN You need to install to use the featureNames and Functions of Part E F G Diagram Diagnosis Procedure Troubleshooting Outline of Post Error Diagnosis by Checking Beep Signal SoundBeep signal sound Error message Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device PC-Diagnostic utility End methodContent of the setup is returned to the setting of the user Test item Stanard Content of standard test Content of enhancing testRecord area frequently accessed All record area is tested Ty of breakdownWiring between Super I/O Content of Standard Test Content of Extend TestExpress Card Connector Test ItemWiring Connection Diagram Removing the Battery Pack and HDD Preparation PackBoard Removing the KB Cable Cover and LCD Cable Cover Removing the GPS PCB and Blue- tooth PCBRemoving the Dimm Cover and Bot- tom Cover Removing the USB PCB and AntennaRemoving the Main PCB Removing the FPC HDD BATRemoving the PAD PCB MP PCB Remove the 4 Screws. N14 PCBRemoving the Handle and Power SW Removing the Display Unit Removing the LCD Rear Cabinet Hinge L and RRemoving the Inverter PCB, TS PCB and LCD Unit Removing the Antenna PCB L and RSetting the Antenna PCB L and R Screws N2 DRHM5054XA Arranging the Antenna L and R CablesSetting the Inverter PCB, TS PCB and LCD Unit Preparation of InverterSetting the LCD Rear Cabinet, Hinge L and R Assembly of LCD UnitSetting the Display Unit Setting the Handle and Power SWFix the Palm Top Cover using the 5 Screws. N4 No1 to Attach the Power LED Packing Sheet to the LED SpacerFix the SW LED PCB using the Screw. N5 Set the SW LED PCBAssembly of Power SW Assembly of Palm Top CoverSetting the I/O PCB Setting the SD PCB, Express Card Setting the Main PCB Connect the 2 Cables to the 2 Connectors. CN17,CN27Fix the Screw. N7 Attach the TOP Screws Assembly of LAN, Modem and MDC Assembly of Main PCBSetting the PAD PCB Assembly of PAD PCBSetting the FPC HDD BAT Preparation of HDD FPC AssyDirection C View Tighten Setting the USB PCB and Antenna PCB Assembly of USB PCB and Antenna PCB Setting the Dimm Cover and Bottom Cover Preparation of Dimm Cover Setting the GPS PCB and Bluetooth PCB Screws N11 DFHE5025XA Screws N12 DXQT2+F3FNLSetting the KB Cable Cover, Keyboard and LCD Cable Cover Arranging the KeyboardSetting the HDD Screws N2 DRHM5054XA Screws N5 DRQT26+D4FKLPreparation oh HDD Assy HDD FPC Ass’yPush and bend HDD Thermal Plate SEC Page Setting the Battery Pack and HDD Pack Set the HDD Pack Set the Battery PackXploded View 18 + 0.22 N.m + 0.2 kgf.cm 2 + 0.02 N.m 10-1CF-30CTQAZBM 10-2314 + 0.0196 N.m 19 + 0.02 N.m216 + 0.0196 N.m 441 + 0.049 N.m10-4 45 + 0.50 N.m 10-510-6 10-7 Replacement Parts List Comparison Table